Makita 5903R 사용 설명서 - 페이지 9
{카테고리_이름} Makita 5903R에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Makita 5903R 13 페이지. 165/190/235 mm
Makita 5903R에 대해서도 마찬가지입니다: 매뉴얼 (15 페이지), 사용 설명서 (13 페이지), 사용 설명서 (13 페이지), 사용 설명서 (12 페이지), 사용 설명서 (13 페이지), 사용 설명서 (16 페이지), 사용 설명서 (13 페이지)
페이지 인쇄
Adjusting for bevel cuts (Fig. 6)
• Loosen the thumb nuts in front and back, and tilt the
tool to the desired angle for bevel cuts (0 – 45°).
Secure the thumb nuts tightly in front and back after
making the adjustment. (5603R, 5703R, 5903R,
5103R)
• Loosen the thumb nut in front and tilt the tool to the
desired angle for bevel cuts (0 – 60°). Secure the
thumb nut tightly in front after making the adjust-
ments. (5143R)
Sighting (5603R, 5703R) (Fig. 7)
For straight cuts, align the right notch on the front of
the base with your cutting line on the workpiece.
For 45° bevel cuts, align the left notch with it.
Top guide (5903R, 5103R) (Fig. 8)
Align your sight line with either the 0° notch for
straight cutting or the 45° notch for 45° angle cuts.
Top guide (5143R) (Fig. 9)
Align your sight line with either the 0° notch for
straight cutting or the 30° notch for 30° angle cuts or
the 45° notch for 45° angle cuts or the 60° notch for
60° angle cuts.
Switch action (Fig. 10)
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
press the lock-off button and pull the switch trigger.
Release the switch trigger to stop.
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to
the ''OFF'' position when released.
Operation (Fig. 11)
Hold the tool firmly. Set the base plate on the work-
piece to be cut without the blade making any contact.
Then turn the tool on and wait until the blade attains
full speed. Now simply move the tool forward over the
workpiece surface, keeping it flat and advancing
smoothly until the sawing is completed. To get clean
cuts, keep your sawing line straight and your speed of
advance uniform.
CAUTION:
• The riving knife should always be used except when
plugging in the middle of the workpiece.
• Do not stop the saw blade by lateral pressure on the
disc.
Guide rule (Fig. 12 & 13)
The handy guide rule allows you to do extra-accurate
straight cuts. Simply slide the guide rule up snugly
against the side of the workpiece and secure it in
position with the screw on the front of the base. It also
makes repeated cuts of uniform width possible.
Joint assembly (Fig. 14 & 15 & 16)
(for connecting a vacuum cleaner)
When you wish to perform clean cutting operation,
connect a vacuum cleaner to your tool. Install the joint
on the tool using the screw. Then connect a hose of
vacuum cleaner to the joint.
MAINTENANCE
CAUTION:
Always be sure that the machine is switched off and
unplugged before carrying out any work on the
machine.
To maintain product safety and reliability, repairs,
maintenance or adjustment should be carried out by a
Makita Authorized Service Center.
9