KitchenAid Superbra KUDA220T 설치 지침 매뉴얼 - 페이지 6
{카테고리_이름} KitchenAid Superbra KUDA220T에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. KitchenAid Superbra KUDA220T 8 페이지. Undercounter dishwasher
페이지 인쇄Floor Damage
Slide dishwasher
onto
cardboard or hardboard before
moving across floor, Failure to
do so may cause damage to
floor covering.
Place drain hose on the left
side of the cabinet opening
between the motor and the frame.
Latch dishwasher door. Grasp
dishwasher by the door frame and
push the dishwasher into the cabinet
opening.
Be careful not to push on
the dishwasher panels. Center
dishwasher in cabinet opening.
Check that front leveling legs are
firmly against the floor.
back of dishwasher
alternate
position
rear cross channel
original position
F_=.=.=.=.=.=.=.=._
_
_--__\\11
_
',',f-'
1121 connec, e,, T
•
street elbow to a 90 °
compression elbow (3/8" NPT one
end). Connect street elbow to water
valve. Connect supply line to
compression elbow. If galvanized
pipe is used, use a second 3/8"
street elbow in place of the
compression elbow.
_F,_
Check that drain
hose is not kinked
drain hose
crimped or contacting
J131
electrical
connections.
Place towel below
•
dishwasher valve area.
Remove red plug from dishwasher
valve. (A small amount of water may
still be in the valve area from quality
I101
assurance testing.) Place hose
Check to see if rear
clamp over dishwasher valve,
•
cross channel contacts
Connect drain hose to valve and
drain, electrical or water lines. If the
secure with hose clamp. Check for
channel contacts any line, pull
good fit and that there are no bends
dishwasher out of opening.
Do
or kinks in drain hose that could
Not remove the channel.
Remove
restrict water flow.
both cross channel screws on the
top mounting
right-hand side. Remove the bottom
/brackets_.
screw on the left-hand side and
"-----'_._"
_----------.--
loosen the top screw. Align the
bottom hole in the loose end of
channel with the higher hole in
frame and attach with screw.
Tighten the top screw on the other
end of channel.
Repeat step 9.
Ill A,,on ,shwas,er oor
•
with cabinet front, not doors.
Do Not drop
screws
into tub.
114
I Open dishwasher
and
•
remove foam shipping
pieces for upper corners of door.
Remove bottom rack. Place a
newspaper or large sheet of paper
over bottom of dishwasher to protect
the pump area when securing
dishwasher to countertop.
Page 6
t
I15.
DicSaC_e%netlbrtCkpetSrner
s
of flange.
Reattach brackets with
bracket end facing away from
dishwasher.
Drill starter holes 3/4"
deep through bracket holes into the
underside of countertop using a 1/8"
drill bit. Do not exeed 3/4" depth.
Attach brackets to underside of
countertop.
Make sure the screw
heads do not interfere with the door.
You MUST secure dishwasher to
keep it from tilting when door is
opened or closed, Do Not drop
screws In dishwasher tub. If
screws should fall into the pump,
pump and motor failure may
occur.
Remove paper from bottom
of dishwasher.
If brackets cannot be attached to
countertop, Do Not disconnect
brackets.
Attach dishwasher to floor
using 1/4"lag bolts through hole in
each side of dishwasher frame.
equally spaced
-1
116
1 Open d°°r appr°ximately
•
3,, and check for equal
spacing between inner door and
tub sides.
If necessary, loosen
screws that fasten dishwasher to
countertop and shift tub. Retighten
screws.