KitchenAid W10579120A 사용자 설명서 - 페이지 7

{카테고리_이름} KitchenAid W10579120A에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. KitchenAid W10579120A 17 페이지.

페이지 인쇄

Scan the code at left with your mobile device, or visit https://kitchenaid.custhelp.com for recommendations that

may help you avoid a service call.

If you experience

The Clean light is

Check the following:

flashing

Is the overfill protection float able to move up and down freely? Press down to release.

Be sure the water supply is turned on to the dishwasher. (This is very important following the new installation of your

dishwasher.)

Check for suds in the dishwasher. For more information on suds, see "Dishwasher does not clean completely."

Dishes do not dry

NOTE: Plastic and items with nonstick surfaces are difficult to dry because they have a porous surface which tends to

completely

collect water droplets. Towel drying may be necessary.

Use of rinse aid along with the Heat Dry or ProDry™ option is needed for proper drying.

Proper loading of items can affect drying.

For improved results, place items on the more slanted side of the rack.

Glasses and cups with concave bottoms hold water. This water may spill onto other items when you are unloading the

dishwasher.

Unload the bottom rack first.

Spotting/Filming

NOTES:

Liquid rinse aid is necessary for drying and to reduce spotting.

Use the correct amount of detergent.

Confirm that the cloudiness is removable by soaking the item in white vinegar for 5 minutes. If the cloudiness disappears, it

is due to hard water. Adjust the amount of detergent and rinse aid (see "Dishwasher Care" section). If it does not come

clear, it is due to etching.

Be sure the incoming water temperature is set at 120°F (49°C).

Try using the Hi-Temp Wash or Sani Rinse options.

To remove spotting, see "Dishwasher Care" section.

Dishwasher does

Be sure the dishwasher is loaded correctly. Improper loading can greatly decrease the washing performance (see

not clean

Operating Your Dishwasher" section).

completely

Check filter to ensure it is properly installed. Clean it if needed. (See "Filtration System" in full User Guide for details.)

Select the proper cycle for the type of soils. The ProWash™ or Tough cycle can be used for tougher loads.

Be sure the incoming water temperature is at least 120°F (49°C).

Use the proper amount of fresh detergent. More detergent is needed for heavier-soiled loads and hard water conditions.

Scrape food from dishes prior to loading (do not prerinse).

If foam or suds are detected by the dishwasher sensing system, the dishwasher may not operate properly or may not fill

with water.

Suds can come from:

Using the incorrect type of detergent, such laundry detergent, hand soap, or dish detergent for hand washing dishes.

Not replacing the rinse aid dispenser cap after filling (or refilling) the rinse aid.

Using an excessive amount of dishwasher detergent.

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or furnished with

the product, KitchenAid brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter "KitchenAid") will pay for factory specified parts and repair

labor to correct defects in materials or workmanship that existed when this major appliance was purchased. Service must be provided by a KitchenAid

designated service company. YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS

PROVIDED HEREIN. This limited warranty is valid only in the United States or Canada and applies only when the major appliance is used in the

country in which it was purchased. Proof of original purchase date is required to obtain service under this limited warranty.

PROBLEM SOLVER

WARRANTY

KITCHENAID

DISHWASHER WARRANTY

LIMITED WARRANTY