Makita AN613 사용 설명서 - 페이지 2
{카테고리_이름} Makita AN613에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Makita AN613 11 페이지. Pneumatic coil nailer
페이지 인쇄
SPECIFICATIONS
Model:
Air pressure
Applicable nails
Nail length (L) x Shank diameter (D)
Nail capacity
Minimum hose diameter
Dimensions (L x W x H)
Net weight
•
Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
•
Specifications may differ from country to country.
SAFETY WARNINGS
Important safety instructions
For personal safety and proper operation and
maintenance of the tool, read this instruction
manual carefully before using the tool.
WARNING: WHEN USING THIS TOOL, BASIC
SAFETY PRECAUTIONS SHOULD ALWAYS BE
FOLLOWED TO REDUCE THE RISK OF PERSONAL
INJURY, INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
Personal Protective Equipment
1.
Always wear safety glasses to avoid eye injury
from dust or fasteners. The safety glasses
should conform with the requirements of ANSI
Z87.1.
WARNING:It is an employer's responsibility to
enforce the use of safety eye protection
equipment by the tool operators and by other
persons in the immediate working area.
2.
Wear hearing protection to protect your ears
against exhaust noise and head protection.
Also wear light but not loose clothing. Sleeves
should be buttoned or rolled up. No necktie
should be worn.
Flammable Atmospheres
1.
Do not operate tool in explosive atmospheres,
such as in the presence of flammable liquids,
gases or combustible dust.
Tool modification
1.
The tool should not be modified unless
authorized in the tool manual or approved in
writing by the tool manufacturer.
0.49 - 0.83 MPa (70 - 120 PSIG)
Wire-collated coil nails (collation angle 15°)
Sheet-collated coil nails (collation angle 15°)
L: 38 mm - 65 mm x D: 2.3 mm - 2.5 mm
(L: 1-1/2" - 2-1/2" x D: 0.090" - 0.099")
275 mm x 127 mm x 319 mm
(10-7/8" x 5" x 12-1/2")
Tool maintenance
1.
Refer to the tool maintenance instructions for
detailed information on the proper
maintenance of a tool.
Recommended fasteners and accessories
1.
Use only fasteners made or recommended by
the tool manufacturer, or fasteners that
perform equivalently to those recommended
by the manufacturer.
2.
Use only accessories made or recommended
by the tool manufacturer, or accessories that
perform equivalently to those recommended
by the manufacturer.
Inspect tool before operating to:
1.
Use only power source specified in the
instruction manual.
Operate the tool within the specified air
pressure on the tool label for safety and longer
tool life. Do not exceed the recommended max.
operating pressure. The tool should not be
connected to a source whose pressure
potentially exceeds 1.38 MPa (200 PSIG).
2.
Never use the tool with other than compressed
air. If bottled gas (carbon dioxide, oxygen,
nitrogen, hydrogen, air, etc.) or combustible
gas (hydrogen, propane, acetylene, etc.) is
used as a power source for this tool, the tool
will explode and cause serious injury.
3.
Always check the tool for its overall condition
and loose screws before operation. Tighten as
required.
4.
Make sure all safety systems are in working
order before operation. The tool must not
operate if only the trigger is pulled or if only
the contact element is pressed against the
wood. It must work only when both actions are
performed. Test for possible faulty operation
with fasteners unloaded and the contact
element in fully pulled position.
5.
Always check contact element as instructed in
this manual. Fasteners may be driven
2 ENGLISH
AN613
200 - 300 pcs.
6.5 mm (1/4")
2.2 kg (4.9 lbs)