KitchenAid 9752397 설치 지침 매뉴얼 - 페이지 6

{카테고리_이름} KitchenAid 9752397에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. KitchenAid 9752397 7 페이지. 30" (76.2 cm) sealed burner gas freestanding and slide-in ranges, with self-cleaning thermal/convection oven

페이지 인쇄

120.1

Plug power supply cord into

earthed/grounded

outlet. "8888" should

appear in clock display.

125

Remove the oven rack. Remove the

oven bottom and place it on a protected

surface.

130

Check the operation of the

oven broil burner. Close the oven door.

Press the "BROIL' pad. "500°F" will

appear in the temperature

display. Press the "Start"

pad. The oven broil burner

should

light in 50 to

60 seconds.

This delay is normal. The oven

safety valve requires a certain time before it will

open and allow gas to flow. The first time broil

burner is lighted, it may take longer to light

because of air in gas line. The first few times

burner is used sparks may appear. This is normal.

NOTE: Oven door must be shut for broil burner to

operate.

1211

Remove vent cap, cooktop burner caps

and grates from parts package. Align

notches in burner caps with pins in

burner base. Burner caps should be level when

properly positioned. Place burner grates over

burners and caps. Place vent cap over vent dome.

126.1

Check the operation of the oven

burner. Push the "BAKE" pad and

"350°F" will appear in the temperature

display. Press the "Start" pad. "LO" will appear in

the display; then "170°F." The oven burner should

light in 50 to 60 seconds-This

delay is normal.

The oven safety valve requires a certain time

before it will open and allow gas to flow.

Electric

ignitors

are used to light the oven and

broil burners.

Do Not insert any object into the opening

of the

protective

shield that surrounds

the ignitor.

Do Not clean the area.

131.1

Look through oven window to check

broil burner for proper flame. The flame

should have a uniform, light blue

appearance

around the burner surface. No yellow

tips, blowing or lifting of the flame should occur.

NOTE: The first few times the broil burner is used,

yellow sparks may appear in the flame. This is

normal and will stop after burner has been used a

few times.

burner

base

prpJ

burner for proper

flame. This flame

should have a l/2"

Electronic

Ignition

System -

Initial lighting

and gas flame adjustments.

Cooktop and oven burners use electronic ignitors

in place of standing pilots. When the cooktop

control knob is turned to the "HI" position, the

system creates a spark to light the burner. This

sparking continues

until the burner has a flame.

When the oven control is turned to the desired

setting, a glow bar heats up bright orange and

ignites the gas. No sparking occurs and the glow

bar remains on while the burners operate.

132

Press the "Cancel/Off"

pad. If the

broil burner flame needs adjustment,

contact your KitchenAid

dealer or

authorized

service company for assistance.

(1.3 cm) long inner

'oven burner

cone of bluish-green,

with an outer mantle of dark

blue, and should be clean and soft in character. No

yellow tips, blowing or lifting of flame should occur.

133

Insert storage

drawer into

slide rails on

sides of drawer opening.

Lift front of drawer slightly

and push firmly to close

drawer.

I .

air shutter

oven

air sh

locati

OFF

Check the

operation of

the cooktop

burners. Push in and

turn each control knob

to the "HI" position. The

flame should light within

4 seconds. The first time

a burner is lighted it

may take longer than

4 seconds to light

because of air in gas

line.

L.P. gas conversion

No attempt-shall

be made to convert

the range

from the gas specified

on the model/serial

rating plate for use with a different

gas without

consulting

the servicing

gas supplier.

An L.P.

Gas Conversion

Kit is included

in your

literature

package.

oven burner

brass

orifice

hood

(nut)

(28

If the oven flame needs to be adjusted,

locate the air shutter near the center

rear of range. Loosen the locking screw

and rotate the air shutter until the proper flame

appears. Tighten locking screw.

123.1

If burners do not light properly, turn

cooktop control knob to the "OFF"

position. Check that the power supplv

To get the most efficient

use

from your new range, read your

Use and Care Guide. Keep

Installation

Instructions

and

Guide close to range for easy

reference.

129.1

Push "Cancel/Off"

pad. Insert oven

bottom tabs into slots in oven burner

area. Check that tabs are correctly

placed in slots. If the oven bottom is not

positioned

properly,

poor baking performance

could occur. Replace oven racks.

cord is plugged in and the circuit breaker or fuse

has not blown, Check that the gas shutoff valves

are set to the "OPEN" position. Repeat Step 22. If

a burner does not light at this point, contact your

KitchenAid dealer or authorized

service company

for assistance.

m-l

Adjust

the height of top burner

. flames (some models)

The cooktop LOW burner flame should be a steady

blue flame approximately

l/4" (0.64 cm) high. It

can be adjusted using the adjustment screw in the

center of the valve stem. The valve stem is located

directly underneath

the control knob.

If the LOW flame needs to be adjusted:

a. Remove the control knob.

b. Hold the knob stem with a pair of pliers. Use

a small flat-head screwdriver to

turn the screw located in the

center of the control knob stem

until the flame is the proper

v/m

size.

Replace the

Control

adjustment

knob.

screw

d. Test the flame bv

turning the contiol from

"LO" to "HI", checking the

flame at each setting-.

Top burner flame appearance:

low flame

wwwww

Panel