Makita BMR100 사용 설명서 - 페이지 8

{카테고리_이름} Makita BMR100에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Makita BMR100 20 페이지. Makita bmr100: specifications
Makita BMR100에 대해서도 마찬가지입니다: 부품 분석 (3 페이지), 사용 설명서 (9 페이지)

페이지 인쇄

3. BH2433 | BH2420After back up batteries are inserted,

insert the main battery pack to power radio. The

suitable battery packs for this radio listed as below.

Cluster Battery:

9.6V: 9135 | 9134 | 9122 | PA09 | 9120

12V:

1235 | 1234 | 1222 | PA12 | 1220

14.4V: 1435 | 1434 | 1422 | PA14 | 1420

18V:

1835 | 1834 | 1822 | PA18

Slide Battery:

9.6V: BH9033 | BH9033A | BH9020 | BH9020A

12V:

BH1233 | BH1233C | BH1220C

14.4V: BH1433 | BH1420 | BL1430

18V:

BL1830

24V:

BH2433 | BH2420

The following tables indicate the operating time on a

single charge.

Battery Cartridge•Voltage

Battery

Capacity

9.6V

12V

PA09

PA12

1.3 Ah

9120

1220

9122

1222

2.0 Ah

BH9020

BH1220C

BH9020A

2.6 Ah

9134

1234

3.0 Ah

9135

1235

BH9033

BH1233

3.3 Ah

BH9033A

BH1233C

* Operating time may differ by the type of battery, charging or

operating conditions.

3-1. Installing or removing Slide

battery cartridge (Fig. 3)

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

• To remove the battery cartridge, withdraw it from the

tool while sliding the button on the front of the cartridge

or pressing the buttons on both sides of the cartridge.

3-2. Installing or removing Cluster

battery cartridge (Fig. 4)

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

• To remove the battery cartridge, withdraw it from the

Job site radio.

4. Replace battery compartment locker.

Operating time*

(At Max. Volume)

14.4V

18V

24V

PA14

PA18

–

Approx. 7 hour

1420

1422

1822

BH2420

Approx. 11 hour

BH1420

1434

1834

–

Approx. 13 hour

1435

1835

–

Approx. 16 hour

BL1430

BL1830

BH1433

–

BH2433 Approx. 17 hour

5. Reduced power, distortion and a "stuttering sound" or

low battery sign

all the signs that the main battery pack needs to

replace.

Note:

The battery pack can't be charged via the supplied AC

power adaptor.

6. When low battery sign

on flashing is the time to replace the back up batteries.

Installing the Soft bended rod

antenna (Fig. 5)

Install the Soft bended rod antenna as show in the figure.

Using Supplied AC power adaptor

(Fig. 6)

Remove the rubber protector and insert the adaptor plug

into the DC socket on the front side of the radio. Plug the

adaptor into a standard mains socket outlet. Whenever

the adaptor is used, the battery pack are automatically

disconnected. The AC adaptor should be disconnected

from the main supply when not in use.

Setting the clock

1. Clock can be set either when the radio is power on or

off.

2. Display will show "-: - -" when the back up batteries

are installed.

3. Long press the time set button

2 seconds, display will flash time set symbol

also the hour digit, followed by a beep.

4. Rotate Tuning control to set the required hour.

5. Press

button to confirm hour setting, the minute

digit will flash.

6. Rotate Tuning control to set the required minute.

7. Press the

button again to complete clock setting.

Operating the radio

This radio equips with three tuning methods – Scan

tuning, Manual tuning and Memory presets recall.

Scan Tuning

1. Press the Power button to turn on the radio.

2. Select the required waveband by pressing the Band

button. Make sure the rubber bended rod antenna has

been well placed for best FM reception. For AM (MW)

band, rotate the radio to get best signal. Try to avoid to

operate the radio next to computer screen and other

equipment which will cause interference to the radio.

3. Press and release Scan button (long press Scan

button more than 2 seconds will activate time setting),

LCD display will flash Scan symbol and the radio will

up search and stop automatically when it finds a radio

station,. Press the Scan button again to pick up the

found station.

that appears on the display are

appears and an "E" keeps

for more than

and