GARDEN MASTER GM3015 조립 지침 - 페이지 2

{카테고리_이름} GARDEN MASTER GM3015에 대한 조립 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. GARDEN MASTER GM3015 2 페이지. Sloping roof shed

페이지 인쇄

If you feel confident that you do not need to read through these instructions, see page 2....

If you choose to vary from these instructions your warranty will be impaired.

Basic overview of what I am trying to achieve...

"For those of us who do not like reading instructions...."

Just join the sheets together and fit the channels to the top and bottom of the sheets as a

framing to make 4 walls and the roof. Follow these basic steps:....

Front Wall:

Layout (A) 1980mm sheet, (C) sheet with door jamb attached and (D) door

with the sheet attached beside them to your preferred configuration and join sheets. Cap the

sheets with (F) 3000 channels (2 sided cutout - Top and 1 sided cutout - bottom). Use (H)

Door spacers to make sure door fits gap OK (they sit on top of the jambs). Drill & Fix (Rivet

or screw) at every 2nd rib. Attach door spacer at each end thru door jambs and channels. 4

fixings underneath into sheeting pan top and bottom. Fit padbolt.

Back:

Join 4 (A) 1830mm Sheets together. Cap with (F) Channels and fix thru every 2nd rib

and at least 1 fixing per sheet thru the back of the channel into the pan of the sheeting. More

in high wind areas.

Roof

: Join 4 (A) 1830mm Sheets together. Cap with (E) 3000mm Channels. Fix @ every 2nd rib. Attach (G)

1830 "L"s to ribs at each end of sheeting at corners and 600mm apart in between.

End walls

: Join the 2 (B) sheets together that slope the same way. Cap with (E) 1515mm channels and fix

at corners and every 2nd rib in between. 2 -3 fixings up underneath into pan of sheeting, top and Bottom.

Assembly:

You have now made up your panels. It's just, Join the corners and put the roof on! Make sure

you have at least 6 fixings down each corner when you join the walls. Fix one side of the roof on thru the

(G) "L" into the top channel on one end wall approx 500mm apart. Check overhang and fix to the other end

wall. You now must to fix down thru every 2nd pan in the roof into the top channels on the front and back

walls. More in high wind areas. Please make sure that you have removed all swarf filings as the rust spots

that they produce may hinder any warranty claims.

Generally most fixings are spaced at 300mm apart

Keep fixings in the pans as close to the ribs as possible for added strength.

Ribs will always protrude to the outside of the shed.

Extra internal fixings is strongly recommended in high wind areas.

Detailed instructions with diagrams:....

1: Front Wall

Note that the cutouts go to the inside of the panel to

You will need:

allow easy fitment of end walls on assembly

(A) 1 x 1980 sheet

(D) Pre-hinged door and 740 sheet

(F) 1 top and 1 bottom Channel

(H) 2 x Door spacers

To hinge the door on the

opposite side - simply put

the top channel on the

bottom and bottom on top

Inside

Outside

A.Join (A) 1980 sheet to (D) or

which way door is to swing.

B.Use (H) door spacer to deter-

mine the correct opening size

by placing on the bottom flange

Spacer

of the door jambs. Then fit (F)

channels to tops and bottoms

of sheeting.

Channel

January 09

Rib

Pan

Drawings are diagrammatic and

are not necessarily to detail.

(F) Channels with

cutouts (as shown).

Channels will come short of ends of

sheeting by 10 - 15mm on all panels

C.Outside: Fix channel at corners

and every 2nd rib between and

thru door jambs and spacer

D.Inside: One fixing per sheet at

each end up thru channel under-

side and thru door jambs/spacer

E.Fit padbolt to the outside of door.

Fix through top and bottom

of channels into Door jamb

& spacer

Note: Higher side of channel goes

to inside of shed

Door jamb on inside

Pg 2

If you feel confident that you do not need to read through these instructions, see page 2....

If you choose to vary from these instructions your warranty will be impaired.

2: Back Wall

You need:

2 x (F) Channels

4 x (A) Sheets

(F)

3: Roof

(G)

You need:

2 x (E) Channels

4 x (A) Sheets

2 x (G) "L"s

(E)

4: End Walls

You need:

2 x (B) Sheets - Left

2 x (B) Sheets - Right

2 x (E) Channels per side

(B)

(E)

A. Join 2 Left (B) sheets together to give a slope at the top.

B. Cap sheeting with (E) 1515mm channels.

C. Fix the channels at the corners and every 2nd rib in between.

D. 3 fixings up underneath thru channel into pan of sheet

Perform the same again for the Right side

A. Join 4 (A) sheets together with

2 fixings thru the overlapping

(F)

ribs making sure the ends of the

sheets are flush.

B. Cap sheeting with (F) channels

(A)

putting the cutouts top and bot-

tom same as the front wall.

C. Fix the channels thru the end

(A)

ribs and every 2nd rib between.

D. Make sure you put at least 1

fixing per sheet up thru the un-

derside of the channel into the

pan of the sheet.

A. Join 4 (A) sheets together same as

the back.

B. Cap sheeting with (E) 3000mm

(E)

channels.

C. Fix the channels every 2nd rib but

not the corners at this stage

D. Place the short flange of the "L" on

top of the rib at 1 end. Make sure

ends are flush with sheeting and

(A)

(G)

put 1 fixing in the centre to hold

the "L". Fix the corners thru the

channels and 1 more between the

corner and the centre fixing. Per-

form the same at the other end. 5

fixings ea "L"

Door Brace Kit

A. The Door braces can be fitted now or

after you have assembled your shed.

(E)

B. Tuck one end of the "Z" between the

bottom channel of the inside of the

door and the sheet. Do the same at the

top overlapping in the centre behind the

padbolt. If you have a locking "T" handle

you will have to run the "Z"s the oppo-

site way to the diagram.

C. Fix the "Z"s at the ends and in the cen-

tre to the channel it is tucked under and

thru the overlap in the centre. 2 or 3

Channels will end

15 - 20mm short

more rivets will be required thru the

at tops of end

door sheeting into the "Z", but they will

walls and 10 - 15

at bottoms

need to be fixed through from the out-

side of the door for

neater appearance.

D. You may need to cut or

bend the flange at the bot-

tom and top of the "Z" if it

catches on door jamb when

opening or closing.

January 09

Pg 3

Inside

Padbolt

"Z" Brace