Garden Oasis RETRO STEEL CLAM GLIDER RED 소유자 매뉴얼 - 페이지 2
{카테고리_이름} Garden Oasis RETRO STEEL CLAM GLIDER RED에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garden Oasis RETRO STEEL CLAM GLIDER RED 2 페이지.
페이지 인쇄PARTS LIST
A
Backrest
2pcs
B
Seat plate
2pcs
C
Armrest
2pcs
D
Crossbar with bracket
2pcs
E
Crossbar
1pc
F
Support base
1pc
G
Connect
4pcs
H
M6x15 bolt
8pcs
I
M6x50 bolt
14pcs
J
M6x45 bolt
6pcs
K
φ
6 metal washer
58pcs
L
φ6 plastic washer
8pcs
M
M6 nut
22pcs
N
M6 bolt cap
27pcs
ASSEMBLY
Note: Leave nuts half-tightened and do not cover the bolt cap during assembly until unit is completely assembled, then
finish tightening nuts and cover the bolt cap accordingly.
Step 1: Attach one of Backrest (A) to a Seat plate (B) with 4 M6 x 15 bolts (H), 8 6 metal washers (K) and 4 M6 nuts (M).
Repeat the same procedure for the other Backrest (A) and Seat plate (B).
Step 2: Attach one of Crossbar with bracket (D) to the bottom hole on the front side of armrest (C) with 1 M6 x 50 bolt (I),
φ
1 6 metal washer (K). Repeat the same procedure for the other side.
Step 3: Attach one of Crossbars (E) to the bottom hole on the rear side of armrest (C) with 1 M6 x 50 bolt (I), 1 6 metal
washer (K). Repeat the same procedure for the other side. Do the same procedure for the Crossbar with bracket (D) as
Crossbar (E) to the middle hole on the rear side of Armrest (C).
Step 4: Place the 2 assembled Backrest and Seat plate onto the assembled armrest. Half-tighten the armrest with bracket
with 1 M6 x 45 bolt (J), 2 6 metal washers (K), 1 6 plastic washer (L), and 1 M6 nut (M). Repeat the same procedure
φ
φ
for the other side.
Step 5: Half-tighten 2 backrests and the bracket on Crossbar (D) with 1 M6 x 45 bolt (J), 2 6 metal washers (K), 2 6
plastic washer (L), and 1 M6 nut (M)
Step 6: Half-tighten the armrest (C) and Seat plate (B) with 1 M6 x 45 bolt (J), 2 6 metal washers (K), 1 6 plastic
washer (L), and 1 M6 nut (M). Repeat the same procedure for the other side.
Step 7: Half-tighten the 2 Seat plates and the bracket of Crossbar (D) with 1 M6 x 45 bolt (J), 2 6 metal washers (K), 2 6
plastic washers (L), 1 M6 nut (M)
Step 8: Attach the one of Connect (G) to Support base (F) with 1 M6 x 50 bolt (I), 2 6 metal washers (K), and 1 M6 nut (M).
Repeat the same procedure for the rest of connects (G).
Step 9: Place chair assembly on the support base (F), screwing the connect (G) to the Armrest (C) with 1 M6 x 50 bolt (I), 2
φ
6 metal washers (K), 1 M6 nut (M). Repeat the same procedure for the rest of connects (G).
Tighten all nuts and cover the bolts with M6 bolt cap (N) accordingly
(
Tools Required: Open end wrench provided
If you any questions regarding assembly of this product,or need additional parts,pleasecontact NSI at
1-877-998-1697from 9:00AM to 5:00 PM EST Monday to Friday or email
.
for assistance
View the expanded assortment of outdoor living product on-line at
WWW.kmart.com and WWW.sears.com
COMPLETED
φ
φ
φ
φ
φ
)
Page1
A
B
φ
L
K
N
J
φ
φ
STEP4
φ
L
K
J
N
STEP6
K
H
M
K
N
STEP1
D
REAR
D
E
STEP3
K
L
L
M
K M
K
J
N
STEP5
L L
N
K
J
K
K
M
STEP7
Page2
FRONT
K
I
N
C
C
D
STEP2
K
I
N
K
M
K
I
N
G
STEP8
F
G
K
K
M
I
N
STEP9
Printed in China