KitchenAid YKGRT607HW5 설치 지침 매뉴얼 - 페이지 6

{카테고리_이름} KitchenAid YKGRT607HW5에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. KitchenAid YKGRT607HW5 14 페이지. 30" freestanding and slide-in sealed burner gas range with self-cleaning thermal/convection oven

페이지 인쇄

I Plug power supply cord into

earthed/grounded

outlet. "8888" should

•

appear in clock display.

[21

IRem°ve

vent cap' c°°kt°p

burner

caps

•

and grates from parts package. Align

notches in burner caps with pins in

burner base. Burner caps should be level when

properly positioned. Place burner grates over

burners and caps. Place vent cap over vent dome.

burner

cap' '

vent

dome

Electronic

Ignition

System

Initial lighting and gas flame adjustments.

Cooktop and oven burners use electronic ignitors

in place of standing pilots. When the cooktop

control knob is turned to the "LtTE" position, the

system creates a spark to light the burner. This

sparking continues as long as the control knob is

turned to "LITE".

When the oven control is turned to the desired

setting, a glow bar heats up bright orange and

ignites the gas. No sparking occurs and the glow

bar remains on while the burners operate.

[22 lCheck

the

operation of

OFF

•

the cooktop

burners. Pushinand

_ I(_

turn each control knob

to the "LITE" position.

The flame should light

within 4 seconds. The

first time a burner is

_ _',,_,.

lighted it may take

4,_, • o_

longer than 4 seconds

4,yo " e _ • _ _o

to light because of air in

4q_D M_o

gas line.

I If burners do not light properly, turn

cooktop control knob to the "OFF"

•

position. Check that the power supply

cord is plugged in and the circuit breaker or fuse

has not blown. Check that the gas shutoff valves

are set to the "OPEN" position. Repeat Step 22. If

a burner does not light at this point, contact your

KitchenAid dealer or authorized service company

for assistance.

[24

]Adjust

the h eight

oftop burner

• flames

(some models)

The cooktop LOW burner flame should be a steady

blue flame approximately

1/4" (0.64 cm) high. It

can be adjusted using the adjustment screw in the

center of the valve stem. The valve stem is located

directly underneath the control knob.

If the LOW flame needs to be adjusted:

a. Remove the control knob.

b. Hold the knob stem with a pair of pliers. Use

a small flat-head screwdriver to

turn the screw located in the

center of the control knob stem

until the flame is the proper

size.

c. Replace the control adjustment

knob.

screw

d. Test the flame by

turning the control from

"LO" to "HI", checking the

flame at each setting.

Top burner flame appearance:

low flame

high flame

Remove the oven rack. Remove the

oven bottom and place it on a protected

•

surface.

Check the operation of the oven

burner. Push the "BAKE" pad and

•

"350°F '' will appear in the temperature

display. Press the "Start" pad. "LO" will appear in

the display; then "170°F:' The oven burner should

light in 50 to 60 seconds. This delay is normal.

The oven safety valve requires a certain time

before it will open and allow gas to flow.

Electric ignitors are used to light the oven and

broil burners.

Do Not insert any object into the opening of the

protective shield that surrounds the ignitor.

Do Not clean the area.

oven

rear

oven burner

tor

Check the oven burner for proper flame.

This flame should have a 1/2" (1.3 cm)

long inner cone of bluish-green, with an

outer mantle of dark blue, and should be clean and

soft in character. No yellow tips, blowing or lifting of

flame should occur.

oven burner

air shutter

location

air shutter

-- rotate

locking screw

to adjust

for proper

flame

oven burner

brass

orifice hood

(nut)

[28

]lfthe°venflameneedst°beadj

usted,

locate the air shutter near the center

•

rear of range. Loosen the locking screw

and rotate the air shutter until the proper flame

appears. Tighten locking screw.

29 ]

Push "Cancel/Off" pad. Insert oven

bottom tabs into slots in oven burner

•

area. Check that tabs are correctly

placed in slots. If the oven bottom is not

positioned properly, poor baking performance

could occur. Replace oven racks.

] Check the operation of the

oven broil burner. Close the oven door.

•

Press the "BROttJ' pad. "500°F '' will

appear in the temperature display. Press the "Start"

pad. The oven broil burner should light in 50 to

60 seconds. This delay is normal. The oven

safety valve requires a certain time before it will

open and allow gas to flow. The first time broil

burner is lighted, it may take longer to light

because of air in gas line. The first few times

burner is used sparks may appear. This is normal.

NOTE: Oven door must be shut for broil burner to

operate.

Look through oven window to check

broil burner for proper flame. The flame

should have a uniform, light blue

appearance around the burner surface. No yellow

tips, blowing or lifting of the flame should occur.

NOTE: The first few times the broil burner is used,

yellow sparks may appear in the flame. This is

normal and will stop after burner has been used a

few times.

] Press the "Cancel/Off" pad. If the

broil burner flame needs adjustment,

•

contact your KitchenAid dealer or

authorized service company for assistance.

Insert storage drawer into slide rails

on sides of drawer opening. Lift front

•

of drawer slightly and push firmly to

close drawer.

L.P. gas conversion

No attempt shall be made to convert the range

from the gas specified on the model/serial

rating plate for use with a different gas without

consulting the servicing gas supplier. An L.P.

Gas Conversion Kit is included in your

literature package.

To get the most efficient

use

from your new range, read your

Use and Care Guide. Keep

Installation

Instructions

and

Guide close to range for easy

reference.

Panel E