Garden Sun HPS-C-SH 소유자 매뉴얼 - 페이지 9
{카테고리_이름} Garden Sun HPS-C-SH에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garden Sun HPS-C-SH 11 페이지. Tabletop
페이지 인쇄Troubleshooting
If the problem is:
Pilot won't light
Note:
Heater
operates
reduced efficiency below 40ºF
(5ºC)
Pilot won't stay lit
Burner won't light
Burner flame is low
Carbon build-up
Thick black smoke
Maintenance
WARNING
FOR YOUR SAFETY:
• Do NOT touch or move heater for at least 45 minutes
after use.
• Reflector is hot to the touch.
• Allow reflector to cool before touching.
To enjoy years of outstanding performance from your
heater, make sure you perform the following maintenance
activities on a regular basis:
8
And this condition exists:
Cylinder valve is closed
Blockage in orifice or pilot tube
Air in gas line
Low gas pressure with cylinder valve
fully open
at
Igniter fails
Dirt built up around pilot
Connection between gas valve and
pilot assembly is loose
Thermocouple is not operating correctly
G
a
s
p
e r
s s
u
e r
s i
o l
w
B
o l
k c
a
g
e
n i
o
i r
c i f
e
Control knob is not in ON position
G
a
s
p
e r
s s
u
e r
s i
o l
w
Outdoor temperature is less than
and tank is less than 1/4 full
C
o
t n
o r
k l
n
o
b
on HI
Dirt or film on reflector and burner screen
Blockage in burner
Then do this
Open valve
Clean or replace orifice or pilot tube
Open gas line and bleed it (pressing control
knob in) for not more than 1 - 2 minutes or until
you smell gas
Turn cylinder valve OFF and replace cylinder
Use match to light pilot; obtain new igniter and
replace
Clean dirt from around pilot
Tighten connection and perform leak check
Replace thermocouple
T
u
n r
y c
n i l
d
r e
v
a
v l
C
e l
r a
b
o l
k c
a
g
e
Turn control knob to ON
T
u
n r
y c
n i l
d
r e
v
a
v l
40ºF
Use a full cylinder
C
h
e
k c
b
u
n r
r e
a
n
d
Clean reflector and burner screen
Remove blockage and clean burner inside and
outside
Keep exterior surfaces clean.
Use warm soapy water for cleaning. Never use
flammable or corrosive cleaning agents.
While cleaning your unit, be sure to keep the area around the
burner and pilot assembly dry at all times. Do not submerge the
control valve assembly. If the gas control is submerged in water,
do NOT use it. It must be replaced.
a. Keeping the appliance area clear and free from combustible
materials , gasoline and other flammable vapors and liquids.
b. Not obstructing the flow of combustion and ventilation air.
c.Keeping the ventilation opening(s) of the cylinder enclosure
free and clear from debris.
Air flow must be unobstructed. Keep controls, burner,
and circulating air passageways clean. Signs of possible
blockage include:
Normal
e
O
F
F
a
n
d
e r
l p
c a
e
y c
n i l
d
e
O
F
F
a
n
d
e r
l p
c a
e
y c
n i l
d
o
i r
c i f
e
f s
r o
b
o l
k c
a
g
e
Abnormal
r e
r e