KitchenAid KEBC27 설치 지침 - 페이지 3
{카테고리_이름} KitchenAid KEBC27에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. KitchenAid KEBC27 5 페이지. 27" electric built-in single and double ovens
페이지 인쇄
ff codes permit
and a separate
grounding
wire is
used, it is recommended
that a qualified
electrician
determine
that the grounding
path and wire gauge
are in accordance
with bca[ codes.
Do Not ground to a gas pipe.
Check with
a qualified
electrician
if you are not
sure oven is properly
grounded.
Do Not have a fuse in the neutra[ or grounding
circuit.
Oven must be connected to the proper eUectdca[
voUtageand frequency as specified on the
modeU/sedd rating pUate.(The model/serial rating
plate is located on the oven door or on the oven
frame.}
[_ Models rated from 7.3 to 9.6 kW at 240 volts
(5.5 to 7.2 kW at 208 volts} require a separate
@°ampere circuit. Models rated at 7.2 kW and
below at 240 volts (5.4 kW and below at 208
volts} require a separate 30-ampere circuit.
[_ A time-delay fuse or circuit breaker is
recommended.
[_ Connect directly to the fused disconnect (or
circuit breaker box} through flexible, armored
or non-metallic sheathed, copper cable (with
grounding wire}.
[_ Flexible armored cable from appliance should
be connected directly to junction box.
[_ Fuse both sides of the line.
[_ A U.L.qisted conduit connector must be
provided at the junction box.
[_ Do Not cut the conduit.
Wire sizes and connections must conform with the
rating of the appliance and to the requirements of
the National Electrical Code, ANSI/NFPA 70 -- latest
edition (% See Page 1) and all local codes and
ordinances.
if the house has aluminum wiring, follow the
procedure below.
a.) Connect the aluminum wiring to the copper wire
using special connectors designed and
Underwriters Laboratories-listed for joining
copper to aluminum. Follow the electrical
connector manufacturer's recommended
procedure.
b.} Aluminum/copper
connection must conform
with local codes and industry-accepted wiring
practice.
oven,
|
power
supply cable
I
Check oven
_
operation.
CC::S:::::::3c
Use screws to attach
oven to cabinet.
Reattach
side
trim.
Remove
trim screws.
Remove side
trim,
Grasp
oven
frame to lift
oven.
Use screws to
attach
oven to
cabinet.
Reattach
side
trim,
Remove side
trim,
shipping
feet,
Replac
oven
door.
Preparation
Excessive
Weight Hazard
Use two or more people to move and
install oven.
Failure to foitow this instruction can
result in back or other injury.
Important: Use both hands to remove oven
doors.
Do Not use handb or any portion of the front
frame or trim for lifting.
Before moving oven across floor, check that oven
is on shipping base or slide oven onto cardboard
or hardboard.
Do Not remove shipping feet at the front tower
corners of oven.
shipping
feet.
m Turn power supply off. Move oven close to
final position.
Remove and discard shipping materials, tape
and protective film from the oven. Do Not
remove shipping base or shipping feet at the
front bwer corners of oven. The shipping feet
will protect the [ower oven trim until oven is
inserted into cabinet.
, Remove and set aside racks and other parts
from inside oven.
Remove
oven
door.
_
power
\
supply
cable
X
W#_
Remove
_
shipping
feet.
Remove trim
Screws.
Remove
oven
doors.
match on the
hinge
in locked
position
=
door
free
to open
and
c[ose
latch on the hinge
position
= door
ready for removal
Removetrim screw.
Pu[[trim out.
/
Pull top of trim
down.
m Completely open oven door. In both back
corners of the door you will see door latches in the
locked position. Rotate both latches forward to the
unlocked position.
Grasp outside edges of door with both hands.
• Begin closing door, atthe moment the door
stops closing, lift and puii door toward you.
. Set door aside on a protective surface.
3m
Remove trim screws attaching right and
left side trim to oven. Grasp the bottom end of
trim and puil away from oven. Slide top end of
trim downward to remove trim from oven. Take
care not to scratch other surfaces with ends of
trim. Set trim and screws aside on protected
surface.
Page 2