Lexmark 658dfe - X B/W Laser 문제 해결 매뉴얼 - 페이지 5

{카테고리_이름} Lexmark 658dfe - X B/W Laser에 대한 문제 해결 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Lexmark 658dfe - X B/W Laser 13 페이지. Setup sheet
Lexmark 658dfe - X B/W Laser에 대해서도 마찬가지입니다: 매뉴얼 (6 페이지), 사용자 설명서 (12 페이지), 정보 매뉴얼 (19 페이지), 설정 시트 (2 페이지)

페이지 인쇄
Lexmark 658dfe - X B/W Laser 문제 해결 매뉴얼
T
EMPORARILY DISCONNECT OTHER EQUIPMENT
To ensure the printer is working correctly, connect it directly to
the telephone line. Disconnect any answering machines,
computers with modems, or telephone line splitters.
C
HECK FOR JAMS
Clear any jams, and then make sure that Ready appears.
T
C
W
EMPORARILY DISABLE
ALL
AITING
Call Waiting can disrupt fax transmissions. Disable this feature
before sending or receiving a fax. Call your telephone company
to obtain the keypad sequence for temporarily disabling Call
Waiting.
V
M
OICE
AIL SERVICE MAY BE INTERFERING WITH THE
FAX TRANSMISSION
Voice Mail offered through your local telephone company may
disrupt fax transmissions. To enable both Voice Mail and the
printer to answer calls, you may want to consider adding a
second telephone line for the printer.
T
HE PRINTER MEMORY MAY BE FULL
1
Dial the fax number.
2
Scan the original document one page at a time.

Can send but not receive faxes

These are possible solutions. Try one or more of the following:
C
HECK TO SEE IF THE PAPER TRAY IS EMPTY
Load paper in the tray.
C
HECK THE RING COUNT DELAY SETTINGS
The ring count delay sets the number of times the phone line
rings before the printer answers. If you have extension phones
on the same line as the printer, or subscribe to the telephone
company's Distinctive Ring service, then keep the Ring Delay
setting at 4.
1
Type the printer IP address into the address field of your
Web browser.
Note: If you do not know the IP address of the printer, then
print a network setup page and locate the IP address in the
TCP/IP section.
2
Click Settings.
3
Click Fax Settings.
4
Click Analog Fax Setup.
5
In the Rings to Answer box, enter the number of times you
want the phone to ring before answering.
6
Click Submit.
T
HE TONER MAY BE LOW
88 Cartridge low appears when the toner is low.

Can receive but not send faxes

These are possible solutions. Try one or more of the following:
T
F
HE PRINTER IS NOT IN
AX MODE
On the home screen, touch Fax to put the printer in Fax mode.
T
HE DOCUMENT IS NOT LOADED PROPERLY
Load the original document faceup, short edge first into the
ADF or facedown on the scanner glass in the upper left corner.
Note: Do not load postcards, photos, small items,
transparencies, photo paper, or thin media (such as magazine
clippings) into the ADF. Place these items on the scanner glass.
M
AKE SURE THE SHORTCUT NUMBER IS SET UP
PROPERLY
•
Check to make sure the shortcut number has been
programmed for the number that you want to dial.
•
As an alternative, dial the telephone number manually.
5

Received fax has poor print quality

These are possible solutions. Try one or more of the following:
R
-
E
SEND THE DOCUMENT
Ask the person who sent you the fax to:
•
Check that the quality of the original document is
satisfactory.
•
Resend the fax. There may have been a problem with the
quality of the telephone line connection.
•
Increase the fax scan resolution, if possible.
T
HE TONER MAY BE LOW
When 88 Cartridge low appears or when you experience
faded print, replace the cartridge.
M
AKE SURE THE FAX TRANSMISSION SPEED IS NOT SET
TOO HIGH
Decrease the incoming fax transmission speed:
1
Type the printer IP address into the address field of your
Web browser.
Note: If you do not know the IP address of the printer, then
print a network setup page and locate the IP address in the
TCP/IP section.
2
Click Settings.
3
Click Fax Settings.
4
Click Analog Fax Setup.
5
In the Max Speed box, click on one of the following:
2400
4800
9600
14400
33600
6
Click Submit.