Lexmark 945e - X Color Laser 용지 걸림 지우기 매뉴얼
{카테고리_이름} Lexmark 945e - X Color Laser에 대한 용지 걸림 지우기 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Lexmark 945e - X Color Laser 8 페이지. Setup sheet
Lexmark 945e - X Color Laser에 대해서도 마찬가지입니다: 팩스 매뉴얼 (3 페이지), 이메일 매뉴얼 (3 페이지), 문제 해결 매뉴얼 (14 페이지), Ftp 매뉴얼 (2 페이지), 액세서리 설치 매뉴얼 (2 페이지), 설정 시트 (1 페이지)
페이지 인쇄
Lexmark™ X94x
Clearing Jams Guide
Clearing jams
Avoiding jams
The following hints can help you avoid jams:
•
Use only recommended paper or specialty media.
For more information, see the Card Stock & Label Guide
available on the Lexmark Web site at
www.lexmark.com/publications.
•
Do not load too much paper. Make sure the stack height does
not exceed the indicated maximum height.
•
Do not load wrinkled, creased, damp, or curled paper.
•
Flex, fan, and straighten paper before loading it.
•
Do not use paper that has been cut or trimmed by hand.
•
Do not mix paper sizes, weights, or types in the same stack.
•
Store the paper in an appropriate environment.
•
Do not remove trays while the printer is printing. Wait for Load
tray <x> or Ready to appear before removing a tray.
•
Do not load the manual feeder while the printer is printing.
Wait for Load Manual feeder with <x> to appear.
•
Push all trays in firmly after loading paper.
•
Make sure the guides in the trays are properly positioned, and
are not pressing too tightly against the paper.
•
Make sure all paper sizes and paper types are set correctly in
the control panel menu.
•
Make sure all printer cables are attached correctly. For more
information, see the setup documentation.
Understanding jam numbers
and locations
When a jam occurs, a message indicating the jam location appears.
The following illustration and table list the paper jams that can
occur and the location of each jam. Open doors and covers, and
remove trays to access jam locations.
Jam
Area name
Instructions
numbers
1
200–203
Door A
Open Door A, and then
remove the jam.
2
230–231
Door B
Open Doors A and B,
and then remove any
jams.
3
241
Door C
Open Door C, and then
remove the jam.
Open Tray 1, and then
remove any jams.
4
242–244
Door D
Open Door D, and
then remove the jam.
Open Trays 2–4, and
then remove any jams.
1
Jam
Area name
Instructions
numbers
5
250
Multipurpose
feeder
6
280–282
Cover F
Open Cover F, and
then remove the jam.
(Horizontal
Transport Unit)
7
283–284
Door G
Open Door G, and
then remove the jam.
287–288
For staple jams,
289
remove the paper
from the accumulator.
Remove the staple
cartridge, and then
clear the staple jam.
8
284–286
Door H
Open Door H, and
then remove the jam.
Door H is located
between the finisher
output bins.
9
290–295
ADF cover
Open the ADF cover,
and then remove the
jam.
200–203 paper jams
1
Open Door A by lifting the release latch and lowering the door.
CAUTION—HOT SURFACE: The inside of the printer
might be hot. To reduce the risk of injury from a hot
component, allow the surface to cool before touching.
1
Remove all paper
from the
multipurpose
feeder.
2
Flex and stack the
paper.
3
Reload the
multipurpose
feeder.
4
Adjust the paper
guide.