Garden Treasures 247684 매뉴얼 - 페이지 2
{카테고리_이름} Garden Treasures 247684에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garden Treasures 247684 3 페이지. Two tier fountain w/pvc liner
페이지 인쇄•
Operate with freshwater only. Avoid heavily chlorinated water and water with high pH levels.
Preparation
Before beginning assembly, read all warnings and safety precautions. Remove parts from carton.
Compare parts with parts list. If any part is missing or damaged, do not attempt to assemble or use the
product. Contact customer service for replacement.
Estimated time for assembly is 15 minutes.
Tools required for assembly:
•
Inflator (Not included)
Assembly Instructions
1.
Unpack the contents of the box and check to make sure that all items are accounted for and in good condition.
2.
Select a flat, level surface for the assembly and final location of your fountain.
3.
Place the PVC Line Basin flat on a horizontal ground. Fill the PVC Line Basin with appropriate air via valve
and make sure that the center of liner totally flat without wrinkle (Fig.1)
4.
Wedge the outer frames to the edge of the PVC Line Basin in order. (NOTE: Please be careful. Do not
damage the PVC Line Basin while assembling the outer frames). (As shown in Fig.2)
5.
Firstly, Route the water supply tube attached at the bottom of the top fountain from upper basin via cord pipe.
Align the top fountain and upper basin with arrow marking " " first. Attach the top fountain to the upper basin
by lining up the corresponding fitting and turn clockwise until the top fountain locked onto Upper Basin.
Secondly, lead the water supply tube extending from the upper basin through the upper pillar . Align the upper
basin and upper pillar with arrow marking " " first. Attach the upper basin to the upper pillar by lining up the
corresponding fitting and turn clockwise until the Upper basin locked onto Upper pillar. Thirdly, route the water
supply tube extending from the upper pillar through the middle basin via cord pipe. Align the Upper pillar and
Middle basin with arrow marking " " first. Attach the Upper pillar to the Middle basin by lining up the
corresponding fitting and turn clockwise until the Upper pillar locked onto Middle Basin. Finally, route the
water supply tube extending from the Middle basin through the Middle pillar. Align the Middle basin and
Middle pillar with arrow marking "
corresponding fitting and turn clockwise until the Middle basin locked onto Middle pillar (As shown in Fig.3).
Place the pump and pedestal at the center of the PVC Line Basin. (NOTE: Route the pump power cord from
the cord slot on the bottom of the Outer frame). Then route the water supply tube from the pedestal and insert it into the outlet on the pump.
Connect the middle pillar and pedestal by notches. (NOTE: After assembling all parts, please make sure that the pump is levelly located on the
PVC Line Basin and do not press the water supply tube). Attach the trap door to the opening of the pedestal. (As shown in Fig.4)
6.
Fill the PVC Line Basin with clean water. The water level should be approximately 40 mm below the top edge of the outer frame. (As shown in
Fig.5)
7.
Plug the power cord from the pump into the Ground Fault Circuit Interrupter (GFCI) outlet. Turn the power
source on. The product will start to function as intended. (As shown in Fig.6)
8.
To eliminate the possibility of water damage to areas around your fountain, check for leaks and excessive
splashing after the initial setup of your fountain. It is highly recommended that this fountain be placed in an
area that will not be damaged should the area come in contact with liquid.
9.
Do not leave your fountain running for extended periods of time when no one is present to observe the
performance.
10. Check the area around your fountain on a regular basis to ensure that there is no leakage.
Pump Maintenance Instructions
•
Regular cleaning of the pump is necessary.
•
Keep water clean to prolong the life of pump.
•
Clean pump when it is dirty or when a drop in performance is detected. Use warm, soapy water and a stiff
brush for heavily stained surfaces Do NOT use harsh chemicals, as this will damage the surface finish.
•
Failure to clean the pump will result in overheating and voiding of the warranty.
•
Use a filter on pump if available.
•
Disconnect the power and empty the reservoir if the fountain will not be used for an extended time.
•
Do NOT operate fountain in temperatures below 41°F (5°C). Freeze damage may occur. If the fountain is
kept outdoors in freezing temperatures, make sure all water is removed and the unit is completely dry.
To disassemble pump for cleaning:
1.
Always disconnect pump from the power source before cleaning.
2.
Remove the inlet screen and impeller housing.
" first. Attach the Middle basin to the Middle pillar by lining up the
2