Jandy Versa-Plumb CL 460 설치 및 운영 매뉴얼 - 페이지 7

{카테고리_이름} Jandy Versa-Plumb CL 460에 대한 설치 및 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Jandy Versa-Plumb CL 460 20 페이지. Cartridge pool filters
Jandy Versa-Plumb CL 460에 대해서도 마찬가지입니다: 설치 및 운영 매뉴얼 (14 페이지), 설치 및 운영 매뉴얼 (20 페이지)

페이지 인쇄

#12x1" Pan Head

Stainless Steel

Screw (Qty 8)

Anchor

Bracket

(Qty 4)

Filter Tank Anchor Bracket Installation

Figure 3.

Anchor Bracket Installation

Figure 4.

Pressure Gauge/Air Release Assembly

nut and into the ﬁ lter tank. Use the ﬂ ats

on the tank adapter to tighten. Do not

overtighten.

Place the larger, thinner o-ring onto the

gauge housing. Thread the housing into the

coupler on the tank adapter.

Orient the gauge/air release assembly in the

desired position. Raise and thread the locknut

onto the bottom of the gauge/air release

assembly. Hand tighten the nut only. Using

a wrench to tighten the nut may damage the

nut, gauge or air release assembly.

3.4 Filter Plumbing

This ﬁ lter operates under pressure. When clamped

properly and operated without air in the water

system, this ﬁ lter will operate in a safe manner.

If the system can be subjected to higher pressure

than the maximum rating of any component,

install an ASME

approved automatic pressure

relief valve or pressure regulator in the circulation

system. Set the relief valve or pressure regulator to

lowest working pressure of any of the components

in the system.

Place the ﬁ lter on the concrete pad, lined up with

the inlet/outlet pipes (see Figures 5 and 5A).

Cartridge Pool Filters - CL and CV Series Filters

1/4" x 2-1/4" S.S. Tapcon

Screw and S.S. Washer

Drill 5/32" Hole

Tank Bottom

Housing

O-Ring

Tank Adapter

Tank Adapter to Housing

Coupler

O-Ring

#12x1" Stainless Steel Pan

Head Screws (Qty 2)

Drill Two 3/32" Holes

Through Filter Base

Mounting Bracket

Anchor Bracket to Platform Installation

To reduce pressure losses, 2" (minimum) piping is

recommended for plumbing the system.

For best efﬁ ciency use the fewest possible number

of ﬁ ttings. This will prevent a restriction in the

water ﬂ ow.

5.1 The CV model ﬁ lter comes with a Jandy

Sweep Elbow for this purpose. The sweep

elbow also includes a threaded port and plug

so that a ½" hose bib can be connected for

pressure testing. See Figure 7.

5.2 To install the sweep elbow use the following

instructions:

To avoid an electrical shock hazard, which can result

in serious injury or death, ensure that all electrical

power to the system is turned off before approaching,

inspecting or troubleshooting any leaking valves

or plumbing that may have caused other electrical

devices in the surrounding area to get wet.

Follow all filter manufacturer's

instructions. NEVER attempt to

assemble, dis as sem ble or adjust the

filter when there is pressurized air in

the system. Starting the pump while

there is any pressurized air in the

system can cause product failure or

also cause the filter lid to be blown

off, which can cause death, serious

personal injury or property dam age.

Switch off the circuit breaker to the

equip ment and open the air relief valve on

top of the ﬁ lter (leave it open during this

procedure).

NOTE

If the ﬁ lter is below pool level, close the suction and

return line valves to isolate the ﬁ ltration system.

Remove the drain plug from the ﬁ lter. Let the water

drain from the ﬁ lter.

Page 7

Filter Base

Mounting Tab

3-1/2" Thick

(Min.)

Concrete Pad

WARNING