Avaya 1150E 시작하기 - 페이지 2

{카테고리_이름} Avaya 1150E에 대한 시작하기을 온라인으로 검색하거나 PDF를 다운로드하세요. Avaya 1150E 2 페이지. Ip deskphone

페이지 인쇄

Avaya 1150E IP Deskphone installation

Caution: Your Avaya 1150E IP Deskphone is shipped with the stand locked in

position. To avoid damaging your phone, press the wall-mount lever, located under

the base, to release the stand and pull it away from the phone.

Step 1: Remove the stand cover. Pull upward on the center catch as indicated in Figure 2,

and remove the stand cover. The cable routing tracks are now accessible.

Step 2: Connect the AC power adapter (optional). Connect the adapter to the AC adapter

jack in the bottom of the phone. Form a small bend in the cable, and then thread the adapter

cord through the channels in the stand.

Warning: Use your Avaya 1150E IP Deskphone with the approved Avaya AC adapter (model

#N0089601) for this model of phone only.

Note 1: Your Avaya 1150E IP Deskphone supports both AC power and Power over Ethernet

options, including IEEE 802.3af Power Classification 3. To use local AC power, the optional

AC adapter can be ordered separately. To use Power over Ethernet, where power is delivered

over the CAT5e cable, the LAN must support Power over Ethernet, an AC adapter is not

required.

Note 2: You must use CAT5e (or later) cables if you want to use Gigabit Ethernet.

Step 3: Install the headset. Plug the connector into the RJ-9 headset jack marked with the

symbol

)

on the back of the phone, and thread the headset cord through the channels in the

stand, so that the headset cord exits the channel marked with the symbol

Step 4: Install the Ethernet cable. Connect one end of the supplied Ethernet cable to the

back of your phone using the RJ-45 connector marked with the symbol

network cable through the channel marked with the symbol

Step 5: Install the Ethernet cable connecting the PC to the phone (optional). If you are

connecting your PC Ethernet through the phone, connect one end of the PC Ethernet cable to

your phone using the RJ-45 connector marked with the symbol

channel marked with the symbol

(

. Connect the other end to the LAN connector on the back of

your PC.

Step 6: Install additional cables. If applicable, plug in optional USB devices. Connect the

Ethernet cable to the LAN Ethernet connection. If you are using an AC power adapter, plug the

adapter into an ACM outlet.

Step 7: Wall-mount your phone (optional). Your Avaya IP Deskphone can be mounted

either by: using the mounting holes on the bottom of the phone stand (Method A), or using a

traditional-style wall-mount box with RJ-45 connector and 15-cm (6-inch) RJ-45 cord (not

provided) (Method B).

Complete steps 1-7, as needed, before you wall-mount your phone:

Method A: Press the wall-mount lever, and pull the phone away from the stand. Using the

stand cover (the part you removed in step 1), mark the wall-mount holes by pressing the

bottom of the stand cover firmly against the wall in the location where you want to install the

phone. Four small pins on the bottom of the stand cover make marks on the wall. Use the

marks as a guideline for installing the wall-mount screws (not provided). Install the screws so

that they protrude 3 mm (1/8 inch) from the wall, and then install the phone stand mounting

holes over the screw heads as indicated in Figure 3 (Method A). You may need to remove the

)

phone from the wall to adjust the lower screws. When the lower screws are snug, install the

phone on the mounting screws, and then tighten the top screws.

Method B: Attach the 15-cm (6-inch) CAT5e cable, position the stand over the mounting

, and thread the

rivets, and slide the phone down the wall so that the rivets fit into the slots on the stand,

indicated in Figure 3 (Method B).

Step 8: Replace the stand cover. Ensure that all cables are neatly routed and press the

stand cover into place until you hear a click.

(

, and thread it through the

Step 9: Put the phone in the wall-mount position (optional). If you wall-mounted your

phone, put it in the wall-mount position by holding the Tilt lever and pressing the phone

towards the base until the phone is parallel with the base. Release the Tilt lever and continue

to push the phone towards the base until you hear a click. Ensure the phone is securely locked

in position.

Avaya 1150E IP Deskphone installation

Avaya 1150E IP Deskphone controls

1150E IP Deskphone controls:

Controlling volume

Press the up or down volume control key while using your headset to adjust the volume of the

associated device.

Answering a call

Press a DN key or the In-Calls key.

Using Hold and Mute

While on a call, press the Hold key to place your caller on hold. Press the line key to retrieve

your call. The icons next to the line keys indicate held lines, while the Mute LED lights when

Mute is active. Press the Mute key to mute your headset, allowing you to speak privately.

Press the Mute key again to speak with your caller.

Setting the contrast

To adjust the display contrast, press the Services key, select Telephone Options, and select

Contrast Adjustment. Use the up/down arrow keys or up/down context sensitive soft keys to

change the setting.

Setting the language

To select the language used by the local menus, press the Services key twice quickly to open

the local menu. Select 1. Preferences, select 2. Language, and use the up/down arrow keys

to choose the language.

Note: Use the Telephone Options menu to select the language used by call-server features.

Consult the Avaya 1150E IP Deskphone User Guide for more information.

Avaya 1150E IP Deskphone Supervisor configuration

By default, the Avaya 1150E IP Deskphone ships with agent configuration keys. Supervisor

keys are ordered separately.

For more information about the Avaya 1150E IP Deskphone Supervisor configuration, refer to

the Avaya 1150E IP Deskphone User Guide.