Avaya 2007 시작하기 - 페이지 2

{카테고리_이름} Avaya 2007에 대한 시작하기을 온라인으로 검색하거나 PDF를 다운로드하세요. Avaya 2007 2 페이지.

페이지 인쇄

Fig. 1

Fig. 3

Connecting the Avaya 2007 IP Deskphone

Follow these steps to connect the Avaya 2007 IP

Deskphone.

Step 1:

Attach the handset cord, with the longer straight

section into the handset jack on the back of the

phone, then route the straight section of the cord

through the cord guide. Attach the other end of the

handset cord to the handset.

Step 2:

Thread the supplied CAT-5e Ethernet cable

through the bottom of the stand as shown in

Figure 1. If using an optional AC power adapter,

thread the cord through the bottom of the stand. If

connecting your PC through the phone, unplug its

Ethernet cable from the LAN and thread it through

the stand. If using the optional USB mouse or

keyboard, thread its cable through the stand.

Step 3:

Connect the Ethernet cable from your data

network to the RJ-45 connector marked

. If

using an optional AC power adapter, connect to

the AC jack in the bottom of the phone. If

connecting a PC through the phone, connect the

supplied Ethernet cable to the PC and then to the

RJ-45 connector marked

. Plug in any optional

USB devices (see Figure 2).

Fig. 2

Fig. 4

Step 4:

Attach the front edge of the stand by aligning the

two clips on the bottom of the phone with the

matching pivot points on the stand. Depress the tilt

adjusting latch and push the stand firmly into the

phone in the direction illustrated (see Figure 3).

There should be two noticeable clicks when the

stand is correctly attached. Arrange the cords so

that they exit from the rear of the stand in the

channels provided and do not interfere with the tilt

mechanism (see Figure 4).

Step 5:

Connect the Ethernet cable to the LAN Ethernet

connection. If using an AC power adapter, plug

into the nearest outlet. Your system administrator

should provide you with correct installation

information.

Note:

The Avaya 2007 IP Deskphone supports both AC

power and Power over Ethernet options, including

IEEE 802.3af standard power. To use local AC

power with the optional universal AC adapter,

country-specific AC power cables are separately

orderable. To use Power over Ethernet, where

power is delivered over the CAT-5e Ethernet

cable, it must be supported by the LAN

infrastructure.

The Avaya 2007 IP Deskphone gives you multiple

options to make a call. Each of these options is

described in detail in your system-specific user

guide.

Controlling Volume:

The volume control key adjusts ringing, handset,

headset, and speaker volumes. Pressing the

volume control key while using your handset,

headset, or speaker adjusts the volume of the

associated device.

Making a Call with the Handset:

Lift the handset to make a call using the primary

line. Enter the phone number on the dial pad.

When your call is complete, press the GOODBYE

key or return the handset to the cradle. If your

phone is programmed with several line keys, you

may select a line first by tapping a line soft key.

Making a Call with Headset or Handsfree:

Press the HEADSET or HANDSFREE key. Enter

the phone number. When your call is completed,

press GOODBYE.

Using HOLD and MUTE:

While on a call, press the HOLD key to place your

caller on hold. Press the line soft key to retrieve

your call. Held lines are indicated by the icons next

to the line soft keys. Pressing MUTE mutes your

handset, headset, or speaker and allows you to

speak privately. Press MUTE again to speak with

your caller. The LED lights when MUTE is active.

Answering a Call:

Answer a ringing call by lifting the handset, or by

pressing the HANDSFREE or HEADSET key.

Note:

Avaya recommends the use of a stylus to avoid

damage to the LCD touchscreen.