Gardena 11000CLEAR 운영자 매뉴얼 - 페이지 6

{카테고리_이름} Gardena 11000CLEAR에 대한 운영자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Gardena 11000CLEAR 14 페이지. Clear water submersible pump/ dirty water submersible pump
Gardena 11000CLEAR에 대해서도 마찬가지입니다: 운영자 매뉴얼 (16 페이지)

페이지 인쇄

Take care that the pump is located where the inlet open-

ings at the suction base are not obstructed neither com-

pletely nor partly.

Stand the pump on a brick if using in a pond.

If the suction process is close to the minimum water level

at start-up, the suction process may take longer.

1. Immerse the pump.

2. Connect the pump to the mains.

Attention! The pump can start immediately depending

on the float switch setting.

Automatic mode with float switch [ Fig. O1 ]:

By adjusting the float switch

sibility to determine the switching heights. For safe

operation, the float switch must be able to move

freely around the pump.

To adjust the Cut-in and Cut-out Height [ Fig. O1 ]:

The maximum cut-in height and minimum cut-out height

(see 7. TECHNICAL DATA) can be adjusted by pushing the

float switch wire into the float switch lock.

• The higher the cable is clamped, the higher the cut-in

and cut-out height.

• The shorter the length of cable between the float

(5)

switch

and the float switch lock

cut-in height and the higher the cut-out height.

4. MAINTENANCE

DANGER! Risk of injury!

Injury when the product starts accidentally.

v Disconnect the product from the mains before

you maintain the product.

To clean the pump:

DANGER! Risk of injury!

Risk of injury and risk of damage to the

product.

v Do not clean the product with a water jet

(in particular high-pressure water jet).

v Do not clean with chemicals including petrol or

solvents. Some can destroy critical plastic parts.

v Clean the surface of the pump with a damp cloth.

5. STORAGE

To put into storage:

The pump is not frost-proof!

The product must be stored away from children.

1. Disconnect the pump from the mains.

2. Turn the pump upside down until no more water runs

out.

3. Clean the pump (see 4. MAINTENANCE).

4. Store the pump in a dry, enclosed and frost-free place.

(5)

you have the pos-

(A)

, the lower the

1. Push the cable of the float switch

openings of the float switch lock

2. Check that the pump switches off automatically.

CAUTION!

v In order to ensure that the float switch is able to

switch on and off, the cable length between the

float switch and the float switch lock must be at

least 10 cm.

Manual operation [ Fig. O2 ]:

The pump remains permanently in operation because

the float switch is bypassed.

(5)

1. Slide the float switch

the float switch locking device

2. Place the pump on a firm surface.

3. Connect the pump to the mains.

Attention! The pump begins operating immediately.

The pump runs permanently without dry-running protection

due to the bypassed float switch. To avoid damage due to

dry running, only operate under supervision.

The minimum residual water depth (see 7. TECHNICAL

DATA) is only achieved in manual mode because the float

switch already switches off the pump before this when in

automatic mode.

To flush the pump:

After pumping water containing chlorine, detergents or

heavily soiled water, the pump must be flushed.

1. Pump lukewarm water (max. 35 °C), possibly adding

a mild cleaning agent (e. g. detergent) until the pumped

water runs clear.

2. Remove residuals according to the waste disposal laws

applicable in your area.

Disposal:

(in accordance with RL2012/19/EC)

The product must not be disposed of to normal

household waste. It must be disposed of in line

with local environmental regulations.

IMPORTANT!

v Dispose of the product through or via your municipal

recycling collection centre.

(11)

into one of the

(A)

with the cable downwards onto

(A)