Gardena 13000 aquasensor 운영자 매뉴얼 - 페이지 6

{카테고리_이름} Gardena 13000 aquasensor에 대한 운영자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Gardena 13000 aquasensor 14 페이지. Submersible pump/dirty water pump
Gardena 13000 aquasensor에 대해서도 마찬가지입니다: 사용 설명서 (14 페이지), 운영자 매뉴얼 (14 페이지), 사용 설명서 (14 페이지), 사용 설명서 (14 페이지), 사용 설명서 (13 페이지), 사용 설명서 (14 페이지), 운영자 매뉴얼 (14 페이지), 사용 설명서 (14 페이지), 사용 설명서 (15 페이지), 사용 설명서 (11 페이지)

Gardena 13000 aquasensor 운영자 매뉴얼
4. STORAGE
To put into storage:
v Store the pump away from frost before the first frost
sets in.
Disposal:
(in accordance with RL2012/19/EC)
The product must not be disposed of to normal
household waste. It must be disposed of in line with
local environmental regulations.

5. MAINTENANCE

The pumps are virtually maintenance-free.
Flushing the Pump:
After having pumped chlorinated swimming pool water or
other liquids leaving residues, the pump should be rinsed
with clear water.
Cleaning the suction base and impeller [ Fig. M1]:
DANGER! Electric shock!
Risk of injury due to electric shock.
v Disconnect the pump from the mains before
cleaning the suction base and impeller.
1. Unscrew the 6 Phillips screws
0
base
off the pump.

6. TROUBLESHOOTING

Problem
Pump is running,
but doesn't deliver
The pump does not switch on
or off. Pump switches off although
the OFF sensor is in the water
Pump doesn't start or suddenly
stops during operation
9
and pull the suction
Possible Cause
Air cannot escape.
Non-return valve inserted wrongly.
Air locks in the suction base.
Impeller clogged.
When starting the pump, water height
falls below the min. water level.
3
4
Sensors
/
and contacts
dirty.
Thermal overload switch has
switched the pump off due to
overheating.
No power.
IMPORTANT!
Dispose of the product through or via your municipal
recycling collection centre.
0
2. Clean suction base
and impeller
does not become void as a result of this maintenance
work).
3. Reinstall the suction base
9
screws
.
For safety reasons a damaged impeller
be exchanged by the GARDENA Service Centre.
Clean sensors [ Fig. M2]:
The sensors will only work reliably if they are
cleaned regularly (at least every 2 months)!
v Clean the sensors
3
4
/
a dry cloth (do not use hard or sharp objects).
Remedy
v Open pressure line (e. g. kinked
pressure pipe).
v Remove the non-return valve.
v Insert the non-return valve with the
word UP on top.
v Wait for max. 60 seconds until the
pump deaerates automatically over
the vent valve. If necessary, switch
off and start it again.
v Disconnect plug and clean impeller
(see 5. MAINTENANCE).
v Submerge pump deeper.
7
are
v Clean sensors
(see 5. MAINTENANCE).
v Disconnect plug and clean impeller
(see 5. MAINTENANCE).
Observe max. media temperature
of 35 °C.
v Check fuses and electric connec-
tions.
q
(the warranty
0
and screw in the Phillips
q
can only
7
and contact
regularly with
13