Gardena 6000/5 inox automatic 사용 설명서 - 페이지 3

{카테고리_이름} Gardena 6000/5 inox automatic에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Gardena 6000/5 inox automatic 9 페이지. Deep well pump
Gardena 6000/5 inox automatic에 대해서도 마찬가지입니다: 사용 설명서 (9 페이지), 사용 설명서 (17 페이지), 사용 설명서 (9 페이지), 사용 설명서 (9 페이지), 운영자 매뉴얼 (9 페이지), 사용 설명서 (10 페이지)

페이지 인쇄

1. Assembly

2. Safety instructions

Electrical Safety:

DANGER! Electric shock!

With a cut off mains plug, moisture can get

into electrical parts via the mains cable and

cause a short circuit.

v Never cut the mains plug off (e. g. to feed

through wall).

vDon't use the power cable for plugging off.

DANGER! Electric shock!

A damaged pump must not be used.

v In case of damage, please have the pump

checked by our GARDENA Service Centre.

v Before operating the pump, first make

a visual check, if there is any damage of

the pump (esp. regarding power cable and

plug).

In accordance with DIN VDE 0100, Deep Well

Pumps may only be operated in swimming

pools, garden ponds and fountains via

a residual current-operated-circuit-breaker

(RCD) with a nominal residual current

≤ 30 mA. The pump must not be operated

when there are persons in the swimming pool

or garden pond.

For safety reasons, we recommend operating

the Deep Well Pump with a residual current-

operated-circuit-breaker (DIN VDE 0100-702

and 0100-738).

v Please contact your electrician.

The power cable of the pump must be

connected to a socket which is positioned

at a height of max. 1.10m (measured from

ground). Take care that the power cable leads

downwards.

Data indicated on the type plate must match

technical data of the mains supply.

Only use extension cables authorised in

accordance with HD 516.

v Consult your qualified electrician.

v Take care that the electrical connections

are made within dry area, protected from

flooding.

v Keep mains plug dry.

Protect plug and power cable from heat, oil and

sharp edges.

The power cable must not be used for mount-

ing or relocating the pump. For submerging

or lifting / securing the pump, please use the

fastening rope.

In Austria:

In Austria, according to ÖVE B/ EN 60 555

part 1 to 3, pumps which are used in swimming

pools and garden ponds, and equipped with

firm power cable should be fed via an ÖVE

approved isolating transformer – rated voltage

must not exceed 230 V.

In Switzerland:

In Switzerland mobile appliances which

are used outdoors, must be connected via

a residual-current device.

Notes on use:

v Before operation, clear the pressure line

(e. g. open closed valve, closed outlet

connector etc.).

Running dry leads to increased wear or damage

and is to be avoided.

v The pump must be immediately switched off

when water fails to flow.

v Observe max. delivery height.

When connecting the pump to the water

supply system, the country-specific sanitary

regulations must be observed to prevent

water not of drinking water quality being drawn

back in.

v If necessary, contact your sanitary expert.

Sand and other abrasive substances

cause increased wear and reduce the pump's

output. Fibres in the water can block the

turbine.

During operation, the pump must always be

submersed in the water up to the minimum

submersion depth (see 9. Technical Data).

Do not allow the pump to run for more

than 10 minutes against the closed

pressure side (e. g. closed valve, closed

dispenser etc.).

The pump is automatically switched off

on overheating by the built-in thermal motor

protector. After having cooled down,

the motor automatically switches on again

(see 7. Trouble-Shooting).

3. Assembly

Install foot:

The foot enables the pump to stand steadily on the ground.

1. Push the foot

2. Screw the foot

When the pump is placed on the ground, the foot must be fitted

so that the pump does not draw in any sand or dirt particles.

Connecting the hose:

The 40mm (1 1/4") internal thread on the outlet of the Deep

Well Pump can be converted if necessary with the pump fitting

provided

then be connected to the GARDENA Hose Connection System

and the GARDENA Fitting Art. 1723 / 1724.

1. Screw the pump fitting

tighten it manually until the washer

2. Connect pressure hose

3. Tie the fastening rope

fastening rope.

For the best pumping results, connect 25mm (1") hoses with the

GARDENA Suction Hose Fitting Art. 1724 and one hose clamp.

If you need to disconnect the hose frequently from the pump,

we recommend using the GARDENA Pump Connection Set

Art. 1752 in connection with a 19mm (¾") hose.

The built-in non-return valve prevents the water flowing back

through the pump.

4. Operation

Pump water:

For the pump to work, it must be submerged in the water up to

the minimum water level on start-up

a) Without the foot, the pump must be fixed at least 20cm above

the ground.

b) If the foot has been fitted, the pump may be placed on the

ground.

1. Immerse pump on the fastening rope

The mains power cable must not be subjected to tension.

2. Secure the fastening rope

3. When using the pump in deep wells or shafts (from approx. 5m

deep) guide the connecting cable

using clips

4. Plug the power cable

Attention! The pump starts immediately.

>20 cm

onto the pump from below.

to the pump

with the two screws.

to a 33mm (1") external thread. The pump can

onto the outlet of the pump and

fits closely.

to the relevant adapter.

to one of the two eyes

(see 9. Technical Data).

into a well or shaft.

along the fastening rope

into a mains socket.

for the