Gardena 14701 운영자 매뉴얼 - 페이지 6

{카테고리_이름} Gardena 14701에 대한 운영자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Gardena 14701 11 페이지. Battery trimmer
Gardena 14701에 대해서도 마찬가지입니다: 운영자 매뉴얼 (9 페이지)

페이지 인쇄

To charge the battery [ Fig. O1 / O2 / O3 ]:

CAUTION!

v Note the mains voltage! The voltage of the power source must

match the voltage specified on the rating plate of the charger.

For the GARDENA Battery Trimmer Art. 14700-55 / 14701-55 there

is no battery and no charger in the scope of delivery.

Thanks to the intelligent charging process, the charge condition of the

battery is automatically detected and then charged up with the optimal

charge current depending on battery temperature and voltage.

In this way, the battery is treated with care and remains permanently fully

charged when it is stored in the charger.

1. Push the locking button

(A)

and remove the battery

(D)

holder

(C)

2. Connect the battery charger

3. Slide the battery charger

(C)

onto the battery

When the battery charge indicator

the battery is being charged.

When the battery charge indicator

permanently green the battery is completely charged

(Charging time, see 7. TECHNICAL DATA).

4. Examine the charge status regularly while you charge.

5. When the battery

(B)

is completely charged, you can disconnect the

battery

(B)

from the charger

(C)

Meaning of the Indication Elements:

Indication on the charger [ Fig. O3 ]:

Flashing of the Battery

The charging procedure is indicated by flashing of the battery charge

Charge Indicator

(Lc)

indicator

(Lc)

Note: The charging procedure is only possible when the battery

temperature is within the allowable charging temperature range,

see 7. TECHNICAL DATA.

Continuous Lighting

Continuous lighting of the battery charge indicator

of the Battery

the battery is fully charged or that the temperature of the battery is

(Lc)

Charge Indicator

not within the allowable charging temperature range and can therefore

not be charged.

When the battery is not inserted, continuous lighting of the battery

(Lc)

charge indicator

socket outlet and that the battery charger is ready for operation.

Battery charge status indication

After starting the product, the battery charge status indication

is displayed for 5 seconds.

Battery charge status

67 – 100 % charged

34 – 66 % charged

11 – 33 % charged

0 – 10 % charged

If the LED

(L1)

flashes green, the battery must be charged.

If the error LED

(Wp)

is illuminated or flashing, see 6. TROUBLESHOOTING.

To set the working position:

Working position 1 [ Fig. O5 ]:

For standard trimming.

Working position 2 [ Fig. O6 /O7 ]:

Trimming beneath obstacles

The tube can be lowered from standard position 1 to two lowered

positions 2 or 3 for trimming beneath obstacles.

1. Put the trimmer on the floor.

2. Hold the trimmer by the tube

(7)

(10)

push the unlock button

with one finger.

(10)

3. Push the unlock button

and lower the tube

position.

(10)

4. Release the unlock button

and let the tube

Working position 3 (only for Art. 14701) [ Fig. O8 /O9 ]:

Cutting at lawn edges.

CAUTION! The trimmer may only be used when the trimmer head

is locked at 0° or 90°.

To rotate the trimmer head

(1)

position 1.

(B)

from the battery

into a mains socket.

(B)

(Lc)

at the charger flashes green

(Lc)

at the charger illuminates

(Lc)

indicates that

indicates that the mains plug is inserted in the

(P)

on the product [ Fig. O4 / O14 ]:

Battery charge status indication

(L1)

(L2)

(L3)

and

illuminate green

(L1)

and

(L2)

illuminate green

(L1)

illuminates green

(L1)

flashes green

with both hands so that you can

(7)

to the required

(7)

engage again.

to 90°, the tube must be in standard

1. Hold the trimmer by the tube

push the unlock button

2. Push the unlock button

0° to 90° until it engages.

3. Release the unlock button

To adjust the tube length [ Fig. O10 ]:

DANGER!

The product must not be used when the tube is completely

inserted (transport position).

1. Loosen the clamping sleeve

(7)

2. Pull out the tube

to the required length.

3. Tighten the clamping sleeve again

To adjust the position of the additional handle [ Fig. O11 ]:

The position of the additional handle can be adjusted to your body height.

(12)

1. Pull the lever

2. Tilt the additional handle

3. Release the lever

(12)

again.

If the trimmer is correctly set to the body height, the posture is upright and

the trimmer head in working position 1 is tilted forwards slightly.

v Hold the trimmer by the main handle

such a manner that the trimmer head is tilted forwards slightly.

To adjust the plant guard:

– Work position [ Fig. O12 ]

– Park position [ Fig. O13 ]

v Pull off the plant guard

it engages.

To start the trimmer [ Fig. O1 /O14 ]:

DANGER! Risk of injury!

Risk of injury if the product does not stop when you

release the start lever.

v Do not bypass the safety devices or switches. For example do

not attach the start lever to the handle.

The product is provided with a two-switch safety device (start

lever with starting lockout) to prevent the product from being

(P)

turned on by accident.

To start:

1. Put the battery

(B)

into the battery holder

2. Hold the additional handle

3. Hold the main handle

lockout

(15)

forward and pull the start lever

The trimmer starts and the battery charge status indication

displayed for 5 seconds.

4. Release the starting lockout

CAUTION! Avoid contact of the plastic blade and the blade carrier with

hard objects (walls, stones fences etc.) to prevent the plastic blade and

the blade carrier from wearing or breaking.

To stop:

1. Release the start lever

The trimmer stops.

2. Push the locking button

holder

(D)

4. MAINTENANCE

DANGER! Risk of injury!

Cut injury when the product starts accidentally.

v Wait for the plastic blade to stop and remove the battery

before you maintain the product.

To clean the trimmer [ Fig. M1 ]:

DANGER! Risk of injury!

Risk of injury and risk of damage to the product.

(7)

with both hands so that you can

(11)

with one finger.

(11)

and rotate the trimmer head

(11)

(7)

and let the tube

engage again.

(6)

(13)

to the desired position.

(14)

and additional handle

(5)

and put it on into the required position until

(D)

until it audibly engages.

(13)

with one hand.

(14)

with the other hand, slide the starting

(16)

(15)

again.

(16)

(A)

and remove the battery

(B)

from the battery

(1)

from

(13)

(P)