Gardena ComfortCut 23 운영자 매뉴얼 - 페이지 7

{카테고리_이름} Gardena ComfortCut 23에 대한 운영자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Gardena ComfortCut 23 11 페이지. Battery trimmer

페이지 인쇄

v Do not clean the product with water or with a water jet

(in particular high-pressure water jet).

v Do not clean with chemicals including petrol or solvents. Some

can destroy critical plastic parts.

The airflow slots must always be clean.

(17)

1. Clean the airflow slots

with a soft brush (do not use a screwdriver).

2. Clean all movable parts after each operation. Especially remove any

grass and dirt from the protective cover

To clean the battery and the battery charger:

Make sure that the surface and the contacts of the battery and the battery

charger always are clean and dry before you connect the battery charger.

Do not use running water.

v Battery charger: Clean the contacts and the plastic parts with a soft

and dry cloth.

v Battery: Occasionally clean the ventilation slots and the terminals on

the battery using a soft brush that is clean and dry.

5. STORAGE

To put into storage:

The product must be stored away from children.

1. Remove the battery.

2. Charge the battery.

3. Clean the trimmer, the battery and the battery charger

(see 4. MAINTENANCE).

4. Store the trimmer, the battery and the battery charger in a dry,

enclosed and frost-free place.

Disposal:

(in accordance with RL2012/19/EC)

The product must not be disposed of to normal household

waste. It must be disposed of in line with local environmental

regulations.

IMPORTANT!

v Dispose of the product through or via your municipal recycling

collection centre.

Disposal of the battery:

The GARDENA battery contains lithium-ion cells that should

not be disposed of with normal household waste at the end of

its life.

Li-ion

IMPORTANT!

v Dispose of the batteries through or via your municipal recycling

collection centre.

1. Discharge the lithium-ion cells completely (contact the GARDENA

Service).

2. Protect the contacts on the lithium-ion cells against short circuits.

3. Dispose of the lithium-ion cells properly.

6. TROUBLESHOOTING

DANGER! Risk of injury!

Cut injury when the product starts accidentally.

v Wait for the plastic blade to stop and remove the battery

before you troubleshoot the product.

To replace the plastic blade [ Fig. T1 / T2 ]:

DANGER! Risk of cutting injuries!

v Do not use metal cutting elements or spare parts and acces-

sories not intended for use by GARDENA.

If the wear rib

(19)

is no longer visible, the blade carrier

replaced. Contact the GARDENA Service.

The plastic blades may only become worn to half the original

length at most. Only use original GARDENA Spare Blades

(2)

(18)

must be

RotorCut. Spare plastic blades are available from your GARDENA

dealer or directly from GARDENA Service.

• GARDENA Spare Blades RotorCut for Turbotrimmer

To remove the plastic blade:

1. Turn the trimmer over.

2. Push the end of the plastic blade down slightly (A), slide the plastic

(8)

blade

inside through the blade carrier

To insert the plastic blade:

v Slide the new plastic blade

(8)

(18)

the blade carrier

until it audibly engages (click).

When the new plastic blade is correctly inserted, it can be moved more

easily.

Problem

Possible Cause

Trimmer is not cutting

Plastic blade is worn or too

cleanly or not cutting at all

short.

Plastic blade is broken off.

Trimmer vibrates severely

Plastic blade is excessively

worn and creates an unbalance.

Blade carrier is worn.

Trimmer can no longer be

Start lever is stuck.

stopped

Trimmer does not start

Battery is empty.

or stops.

LED

(L1)

is flashing green

[ Fig. O4 ]

Trimmer does not start

Battery temperature is outside

or stops.

the permissible temperature

Error-LED

(Wp)

is illuminated

range.

red [ Fig. O4 ]

There are drops of water or

moisture between the battery

contacts on the trimmer.

Engine is blocked.

Trimmer does not start

Product is defective.

or stops.

(Wp)

Error-LED

is flashing

red [ Fig. O4 ]

Trimmer does not start

Battery is not put completely

or stops.

into the battery holder.

(Wp)

Error-LED

is not

illuminated [ Fig. O4 ]

Battery is defective.

Product is defective.

Charging is not possible.

The battery is not connected

(Lc)

Battery charge indicator

(correctly).

is continuously illuminated

Battery contacts are dirty.

[ Fig. O3 ]

Battery temperature is outside

the permissible charging

temperature range.

Battery is defective.

(Lc)

Battery charge indicator

Mains plug of the charger is

is not illuminated [ Fig. O3 ]

not (correctly) plugged in.

Socket outlet, mains cable or

charger is defective.

NOTE: For any other malfunctions please contact the GARDENA service depart-

ment. Repairs must only be done by GARDENA service departments or specialist

dealers approved by GARDENA.

7. TECHNICAL DATA

Battery Trimmer

Unit

Rated current

Rated voltage

V (DC)

Cutting width

Art. 5368

(18)

(B) and pull out.

from inside through the slot in metal of

Remedy

v Replace the plastic blade.

v Replace the blade carrier.

v Remove the battery and

loosen the start lever

v Charge the battery.

v Wait until the battery tem-

perature is between

0 °C – + 45 °C again.

v Remove the water drops /

moisture with a dry cloth.

v Remove the obstacle.

Start again.

v Contact the GARDENA

Service.

v Put the battery completely

into the battery holder until

it audibly engages.

v Replace the battery.

v Contact the GARDENA

Service.

v Connect the battery to

charger correctly.

v Clean the battery contacts

(e. g. by connecting and

disconnecting the battery

several times. Replace the

battery if necessary.

v Wait until the battery

tem perature is between

0 °C – + 45 °C again.

v Replace the battery.

v Insert the mains plug into the

mains socket (completely).

v Check the mains voltage.

Let the charger be checked

if necessary by an authorised

specialist dealer or the

GARDENA Service.

Value (Art. 14700)

Value (Art. 14701)

2.3