Gardena THS 42 사용 설명서 - 페이지 7

{카테고리_이름} Gardena THS 42에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Gardena THS 42 13 페이지. Accu telescopic hedge trimmer
Gardena THS 42에 대해서도 마찬가지입니다: 사용 설명서 (9 페이지)

페이지 인쇄

2179-20-960-05_04.03.2005.qxd

5. Assembly / setting the working position

5.1 Assembly of the guide

handle (fig. A)

The three-position guide handle

is mounted onto the unit and

secured with 2 screws. (Captive

screws integrated in the handle.)

5.2 Basic working position

settings (fig. B - E)

The Telescopic Hedge Trimmer

has three basic settings. These

are marked

head and the handle:

Trimming hedges from the

side at a distance from the

standing position, eg. to reach

over flower beds (fig. B / B 1).

Note:

Telescopic handle retracted.

For trimming extremely low

hedges, or eg. ground blan-

kets, while standing upright

(fig. C / C 1).

Note: Telescopic handle

extended to the appropriate

length for upright working.

For trimming high hedges

up to approx. 2.5 m from

the ground without the need

for a ladder or scaffolding

(fig. D / D 1).

Note: Telescopic handle ex-

tended to the appropriate

length. Control of the Tele-

scopic Hedge Trimmer is

within arm's reach for easier

handling (fig. D).

6. Operation

Insert the accu

in the re-

ceptacle as illustrated in figure I.

Ensure that the accu snaps in

correctly. Pay attention that this

audibly "clicks" into position.

The accu is released from the

tool by simultaneously pressing

both of the orange coloured

locking buttons.

The Hedge Trimmer is fitted with

a two-hand safety switch to pre-

04.03.2005

5.3 Setting a working position

Attention! The accu must

be disconnected from

the tool and the cutting blade

sheath should remain in posi-

tion when setting the working

position !

Never take hold of the cutting

blade to turn the blade head

or to extend the telescopic

on the blade

handle!

Note: The cutting blade has

a total of 8 working positions

(12° increments from 0°/horizon-

tal to 84° elevation).

Adjustment to any of the 5 inter-

mediate settings for the 3 work-

ing positions described above

is made in the same manner.

The positions

scribed above are recommended

for straight forward handling.

Important! Always ensure that

the selected position snaps in

correctly. Danger of injury!

Select one of the basic working

positions

to the description section 5.2 and

referring to figure E, adjust the

Telescopic Hedge Trimmer as

follows (fig. D / F/ G):

1. (Fig. F) Adjust the length of

the telescopic handle by

pressing and holding the ad-

justing button

ing the telescopic handle to

(fig. H / I)

vent the tool being turned on by

accident. Thus both hands are

required to operate the Hedge

Trimmer (fig. H):

1. Hold by the 3-point guide

handle

the three button switches

2. Hold the grip

hand and depress the button

switch

will then start to run.

10:07

Seite 13

de-

according

while extend-

and press one of

with the other

. The Hedge Trimmer

the desired working length

(fig. F). The length of the tele-

scopic handle can be extended

by max. 310 mm.

2. (Fig. G 1) Press and hold the

oval pimpled button

turning the trimmer head

the axial direction into one of

the working positions

for example into position

for trimming the top of a high

hedge (arrow must point to

the position number – see

figure D 1).

Note: The trimmer head can

be set to one of 7 axial posi-

tions between 0° and 180°

at increments of 30°.

3. (Fig. G 2) Adjust the cutting

angle for the trimmer blade

by pressing and holding the

round adjusting button

adjusting the position of the

trimmer blade

for working

as required.

(Our example: position

Arrow must point to the position

number – see figure D 1).

Note: All 3 working positions

for selection can be set in this

way.

The working position has been

correctly set when the position

number indicates the selected

position (see example figure

D 1).

Simply release either of these

switches in order to stop the

trimmer.

In accordance with safety regu-

lations, an additional safety device

ensures that the blade motion

stops within 1 sec.

The projecting guide (impact

protection) prevents any kick-

back if the trimmer hits a solid

object.

while