Gardena THS 42 2179 사용 설명서 - 페이지 5

{카테고리_이름} Gardena THS 42 2179에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Gardena THS 42 2179 9 페이지. Accu telescopic hedge trimmer

페이지 인쇄

GARDENA Accu Telescopic Hedge Trimmer THS 42

1. Technical data

Voltage

12 V

Rated current (idling)

2 A

Strokes

2,100 / min

Blade length

42 cm

Telescopic extension range

0 - 31 cm

Running time with Accu A 12

25 - 35 min

Weight (without Accu)

3.2 kg

Working area related emission

characteristic value L

73 dB (A)

Noise level L

92 dB (A)

Vibrations a

< 2.5 dB (A)

vhw

2. Notes on operating instructions

Please read these operating in-

operating controls, their correct

structions carefully and observe

use, and the notes on safety.

the notes given.

Use the instructions to familiarise

For safety reasons, child-

yourself with the equipment, the

ren under 16 as well as

persons not familiar with these

3. Introduction

This Hedge Trimmer is one of

1. Accu A 12 (Art. No. 2109) as

the tools in the extensive range

the energy supply / battery

of accu-system V12 equipment

for the accu-system V12.

from GARDENA.

2. Battery Charger NL 12

Please use the following articles

(Art. No. 2105) as the charger

from the accu-system V12 pro-

for the accu-system V12.

gramme to operate this tool:

Alternatively, the Accu-Pack

AP 12 (Art.-No. 2110) can be

used as the energy supply.

4. Proper use

The GARDENA Accu Telescopic

Compliance with the instructions

Hedge Trimmer is designed for

provided by the manufacturer

trimming hedges in domestic

is a prerequisite for using the

gardens and allotments.

tool correctly.

The operating instructions also

Gardening tools for private house-

include the conditions for opera-

holds and gardens are consid-

tion, repair and maintenance.

ered unsuitable for use in public

grounds, parks, sports centres,

in agriculture or forestry.

Measuring method according to

EN 774

directive 2000 / 14 / EC

operating instructions should

not use this Telescopic Hedge

Trimmer.

Keep these operating instruc-

tions in a safe place.

This can be recharged using

the Battery Charger NL 12

or by the High-speed Battery

Charger SL 60 which is avail-

able as an alternative.

Important ! The High-speed

Battery Charger SL 60

(Art. No. 2100) is designed

only for charging the Accu-

Pack AP 12 (Art. No. 2110).

Attention! Because of

the danger of physical

injuries, this tool must not be

used for cutting lawns / grass

verges, or for cutting in the

sense of shredding for com-

posting.

5. Assembly / setting the working position

5.1 Assembly of the guide

5.3 Setting a working position

handle (fig. A)

Attention! The accu must

The three-position guide handle

be disconnected from

is mounted onto the unit and

the tool and the cutting blade

secured with 2 screws. (Captive

sheath should remain in posi-

screws integrated in the handle.)

tion when setting the working

position !

5.2 Basic working position

settings (fig. B - E)

Never take hold of the cutting

The Telescopic Hedge Trimmer

blade to turn the blade head

has three basic settings. These

or to extend the telescopic

are marked

on the blade

handle!

head and the handle:

Note: The cutting blade has

Trimming hedges from the

a total of 8 working positions

side at a distance from the

(12° increments from 0°/horizon-

standing position, eg. to reach

tal to 84° elevation).

over flower beds (fig. B / B 1).

Adjustment to any of the 5 inter-

Note:

mediate settings for the 3 work-

Telescopic handle retracted.

ing positions described above

For trimming extremely low

is made in the same manner.

hedges, or eg. ground blan-

The positions

kets, while standing upright

scribed above are recommended

(fig. C / C 1).

for straight forward handling.

Note: Telescopic handle

Important! Always ensure that

extended to the appropriate

the selected position snaps in

length for upright working.

correctly. Danger of injury!

For trimming high hedges

Select one of the basic working

up to approx. 2.5 m from

positions

the ground without the need

to the description section 5.2 and

for a ladder or scaffolding

referring to figure E, adjust the

(fig. D / D 1).

Telescopic Hedge Trimmer as

Note: Telescopic handle ex-

follows (fig. D / F/ G):

tended to the appropriate

1. (Fig. F) Adjust the length of

length. Control of the Tele-

the telescopic handle by

scopic Hedge Trimmer is

pressing and holding the ad-

within arm's reach for easier

justing button

handling (fig. D).

ing the telescopic handle to

6. Operation

(fig. H / I)

Insert the accu

in the re-

vent the tool being turned on by

ceptacle as illustrated in figure I.

accident. Thus both hands are

Ensure that the accu snaps in

required to operate the Hedge

correctly. Pay attention that this

Trimmer (fig. H):

audibly "clicks" into position.

1. Hold by the 3-point guide

The accu is released from the

handle

tool by simultaneously pressing

the three button switches

both of the orange coloured

2. Hold the grip

locking buttons.

hand and depress the button

switch

The Hedge Trimmer is fitted with

will then start to run.

a two-hand safety switch to pre-

the desired working length

(fig. F). The length of the tele-

scopic handle can be extended

by max. 310 mm.

2. (Fig. G 1) Press and hold the

oval pimpled button

turning the trimmer head

the axial direction into one of

the working positions

for example into position

for trimming the top of a high

hedge (arrow must point to

the position number – see

figure D 1).

Note: The trimmer head can

be set to one of 7 axial posi-

tions between 0° and 180°

at increments of 30°.

3. (Fig. G 2) Adjust the cutting

angle for the trimmer blade

de-

by pressing and holding the

round adjusting button

adjusting the position of the

trimmer blade

as required.

(Our example: position

Arrow must point to the position

number – see figure D 1).

according

Note: All 3 working positions

for selection can be set in this

way.

The working position has been

correctly set when the position

number indicates the selected

position (see example figure

D 1).

while extend-

Simply release either of these

switches in order to stop the

trimmer.

In accordance with safety regu-

lations, an additional safety device

and press one of

ensures that the blade motion

stops within

1 sec.

with the other

The projecting guide (impact

protection) prevents any kick-

. The Hedge Trimmer

back if the trimmer hits a solid

object.

while

for working