Makita UT1305 사용 설명서 - 페이지 6

{카테고리_이름} Makita UT1305에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Makita UT1305 20 페이지. Mixer
Makita UT1305에 대해서도 마찬가지입니다: 브로셔 (2 페이지), 사용 설명서 (16 페이지), 사용 설명서 (13 페이지), 기술 정보 (7 페이지), 사용 설명서 (8 페이지)

페이지 인쇄

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Switch action (Fig. 1)

CAUTION:

• Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

"OFF" position when released.

To start the tool, simply pull the switch trigger. Release the

switch trigger to stop.

For continuous operation, pull the switch trigger and then

push in the lock button.

To stop the tool from the locked position, pull the switch

trigger fully, then release it.

Indicator lamp (Fig. 2)

The green power-ON indicator lamp lights up when the

tool is plugged to the mains. If the indicator lamp is lit but

the tool does not start even if the tool is switched ON, the

carbon brushes may be worn out, or the motor or the

switch may be defective. If the indicator lamp does not

light up, the mains cord or the indicator lamp may be

defective. When the mains cord is defective, the tool

neither starts nor lights the indicator lamp. When the

indicator lamp is defective, the tool starts without the

indicator lamp lighting up.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing shaft

Tighten the shaft with hex. Nut into the shaft holder as far

as the hex nut comes into contact with the holder. (Fig. 3)

Hold the notch in the shaft holder with wrench 19 so that it

cannot revolve. With the notch held so, tighten the hex nut

with another wrench 19 in the direction of arrow. (Fig. 4)

Installing mixing blades

To mount the mixing blade, install it with the "UP" mark on

it facing the tool (directing inside). (Fig. 5)

Install the mixing blade on the top of shaft and secure it

with hex. bolt. (Fig. 6)

In case of mixing blade 150 (accessory), screw it directly

on the top of shaft as it is threaded.

OPERATION

Mixing

CAUTION:

• Do not use to mix flammable material such as paint

with thinner used as solvent. Failure to do so may

cause injury.

• Mixing with the mixing blade floating out of the mixing

material may cause the material to splash about.

1. Hold the rear handle of the tool with one hand and the

grip with the other hand firmly, place the mixing blade

under material fully and turn on the tool after making

sure work site safety.

2. Move the mixing blade up and down during the mixing

operation so that whole part of material can be mixed.

3. When finishing mixing, turn off the tool, make sure that

the mixing blade has come to a complete stop, and

then pull it out of the vessel.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection or

maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Replacing filter (Fig. 7)

Replace the filter regularly as the cooling efficiency of the

tool is reduced due to built-up dust or particles in the filter.

Insert the slotted bit screwdriver and the like between the

tool and the cover as shown in the figure. Lift it up just like

using a shovel and remove the cover.

Replace the filter in the cover with a new one.

Reinstall the cover on the tool.

Replacing carbon brushes

Remove and check the carbon brushes regularly. Replace

when they wear down to the limit mark. Keep the carbon

brushes clean and free to slip in the holders. Both carbon

brushes should be replaced at the same time. Use only

identical carbon brushes. (Fig. 8)

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps. (Fig. 9)

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Mixing blades

• Shaft

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ from

country to country.