KitchenAid KBHS109SSS04 설치 지침 매뉴얼 - 페이지 3
{카테고리_이름} KitchenAid KBHS109SSS04에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. KitchenAid KBHS109SSS04 12 페이지. 27" (68.6 cm) and 30" (76.2 cm) electric built-in microwave oven
KitchenAid KBHS109SSS04에 대해서도 마찬가지입니다: 부품 목록 (8 페이지)
페이지 인쇄
Cabinet
Side View
_A_
_,
B
_
E_
D
/C
A. 23 _" (59.1 cm) min. cutout depth
B. 23" (58.4 cm) recessed oven depth
C. Oven front
D. Recessed oven
E. Cabinet
ect cc} 8®q n m® s s
GROUNDING
INSTRUCTIONS
For a permanently
connected
microwave
oven:
The microwave
oven must be connected to a grounded,
metallic, permanent
wiring system, or an equipment
grounding conductor should be run with the circuit
conductors and connected to the equipment
grounding
terminal or lead on the microwave oven.
SAVE THESE iNSTRUCTiONS
If codes permit and a separate ground wire is used, it is
recommended
that a qualified electrical installer determine that
the ground path and wire gauge are in accordance
with local
codes.
Check with a qualified electrical installer if you are not sure the
microwave oven is properly grounded.
This microwave oven must be connected to a grounded metal,
permanent wiring system.
Be sure that the electrical connection and wire size are adequate
and in conformance
with the National Electrical Code, ANSI/
NFPA 70-latest edition or CSA Standards C22.1-94, Canadian
Electrical Code, Part 1 and C22.2 No. O-M91-1atest edition, and
all local codes and ordinances.
A copy of the above code standards can be obtained from:
National Fire Protection Association
One Batterymarch
Park
Quincy, MA 02269
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
Electrical
Connection
To properly install your microwave oven, you must determine the
type of electrical connection you will be using and follow the
instructions
provided for it here.
•
Microwave oven must be connected to the proper electrical
voltage and frequency as specified on the model/serial
number rating plate. The model/serial
number rating plate is
located on the right-hand microwave oven frame.
A. Model/serial
number plate
When a 4-wire or 3-wire, single phase 120/208 or 120/240
volt, 60 Hz, AC only electrical supply is available, a 20-amp
maximum circuit protection is required, fused on both sides
of the line.
A time-delay fuse or circuit breaker is recommended.
Connect directly to the fused disconnect
(or circuit breaker
box) through flexible, nonmetallic sheathed, copper cable
(with grounding wire). See "Make Electrical Connection"
section.
Flexible cable from the microwave oven should be connected
directly to the junction box.
Do not cut the conduit. The length of conduit provided is for
serviceability
of the microwave oven.
A UL listed or CSA approved conduit connector must be
provided.
If the house has aluminum wiring follow the procedure below:
1. Connect a section of solid copper wire to the pigtail
leads.
2. Connect the aluminum wiring to the added section of
copper wire using special connectors and/or tools
designed and UL listed for joining copper to aluminum.
Follow the electrical connector manufacturer's
recommended
procedure. Aluminum/copper
connection must conform with
local codes and industry accepted wiring practices.