Makita VR003G 사용 설명서 - 페이지 6

{카테고리_이름} Makita VR003G에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Makita VR003G 17 페이지. Cordless concrete vibrator
Makita VR003G에 대해서도 마찬가지입니다: 사용 설명서 (17 페이지), 사용 설명서 (17 페이지)

페이지 인쇄

10. The contained lithium-ion batteries are subject to

the Dangerous Goods Legislation requirements.

For commercial transports e.g. by third parties,

forwarding agents, special requirement on pack-

aging and labeling must be observed.

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required.

Please also observe possibly more detailed

national regulations.

Tape or mask off open contacts and pack up the

battery in such a manner that it cannot move

around in the packaging.

When disposing the battery cartridge, remove

11.

it from the tool and dispose of it in a safe

place. Follow your local regulations relating to

disposal of battery.

12. Use the batteries only with the products

specified by Makita. Installing the batteries to

non-compliant products may result in a fire, exces-

sive heat, explosion, or leak of electrolyte.

13. If the tool is not used for a long period of time,

the battery must be removed from the tool.

14. During and after use, the battery cartridge may

take on heat which can cause burns or low

temperature burns. Pay attention to the han-

dling of hot battery cartridges.

15. Do not touch the terminal of the tool imme-

diately after use as it may get hot enough to

cause burns.

16. Do not allow chips, dust, or soil stuck into the

terminals, holes, and grooves of the battery

cartridge. It may cause heating, catching fire,

burst and malfunction of the tool or battery car-

tridge, resulting in burns or personal injury.

17. Unless the tool supports the use near

high-voltage electrical power lines, do not use

the battery cartridge near high-voltage electri-

cal power lines. It may result in a malfunction or

breakdown of the tool or battery cartridge.

18. Keep the battery away from children.

SAVE THESE INSTRUCTIONS.

CAUTION:

Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

have been altered, may result in the battery bursting

causing fires, personal injury and damage. It will

also void the Makita warranty for the Makita tool and

charger.

Tips for maintaining maximum

battery life

Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

Charge the battery cartridge with room tempera-

ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot

battery cartridge cool down before charging it.

When not using the battery cartridge, remove

it from the tool or the charger.

Charge the battery cartridge if you do not use

it for a long period (more than six months).

FUNCTIONAL

DESCRIPTION

CAUTION:

Always be sure that the tool is

switched off and the battery cartridge is removed

before adjusting or checking function on the tool.

Replacing battery case

Optional accessory

Install one of the battery cases optionally available in

three ranges of sizes to fit your battery cartridge and

cord connected power source.

Fig.1

► 1. Battery case S 2. Battery case L 3. Battery

case H

Open the standard equipped battery case while

pressing the buttons on sides of the case.

Loosen the screws securing the standard

equipped battery case, and slide the battery case off

along the housing.

Fig.2

► 1. Standard equipped battery case 2. Screws

3. Housing

6 ENGLISH