Gardena SmallCut 300 운영자 매뉴얼 - 페이지 5
{카테고리_이름} Gardena SmallCut 300에 대한 운영자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Gardena SmallCut 300 9 페이지. Turbotrimmer
Gardena SmallCut 300에 대해서도 마찬가지입니다: 사용 설명서 (8 페이지), 사용 설명서 (12 페이지), 사용 설명서 (12 페이지), 운영자 매뉴얼 (6 페이지)
페이지 인쇄
2. ASSEMBLY
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Before you assemble the product, make sure that the mains
cable is disconnected.
To assemble the trimmer [ Fig. A1 / A2 ]:
1. Put the top part of the handle
they make a click (click). Ensure that the two arrows
other. The cable must not be stretched or caught when you do this.
2. Put the bottom handle
3
on the top part of the handle
a click (click). Ensure that the two arrows
3. Put the cover
4
on the trimmer head
5
feed the cutting filament
through the opening in the cover
4
4. Put the cover
on the trimmer head
Make sure that all cams lock in position.
3. OPERATION
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Before you connect, adjust or transport the product,
disconnect the mains cable and transport the product by
the bottom handle.
To connect the trimmer [ Fig. O1 ]:
DANGER! Electric shock!
To avoid damage to the mains cable
cable
6
must be inserted into the cable lock
v Before you operate the product insert the extension cable
7
into the cable lock
.
6
1. Loop the extension cable
, insert the loop into the cable lock
pull tight.
8
2. Connect the plug
of the product into the socket
cable
6
.
3. Connect the extension cable
6
Work position [ Fig. O2 ]:
v Hold the product by the top part of the handle
3
handle
so that the trimmer head
Make sure, the filament does not touch hard objects such as walls, stones
and fences to prevent the filament from welding together or breaking.
To start the trimmer [ Fig. O3 ]:
DANGER! Risk of injury!
Risk of injury if the product does not stop when you
release the start button.
v Do not bypass the safety devices or switches. For example do
not attach the start button
To start:
v Push the start button
0
on the top part of the handle
To stop:
0
v Release the start button
.
To extend the cutting filament (Tip mechanism) [ Fig. O4 / O5 ]:
The tip mechanism operates when the motor operates. The best
result occurs only with the maximum cutting filament length. During first
operation, it can be necessary to extend the cutting filament many times.
1. Start the product.
2
2. Hold the trimmer head
parallel to the ground and briefly tap the
2
trimmer head
onto a solid surface (prevent constant pressure for
extended periods).
The cutting filament
5
is automatically extended with a mechanism
that can be heard and adjusted to the correct length with the filament
q
limiter
. If necessary tap many times again and again.
8
1
and the trimmer head
2
together until
>
face each
1
until it makes
B
face each other.
2
while you
4
.
2
until it makes a click (click).
8
the extension
7
.
9
of the extension
into a 230 V mains socket.
1
and the bottom
2
is tilted a small distance forward.
0
to the handle.
1
.
4. MAINTENANCE
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Before you maintain the product, make sure that the mains
cable is disconnected.
To clean the trimmer [ Fig. M1 ]:
DANGER! Electric shock!
Risk of injury and risk of damage to the product.
v Do not clean the product with water or with a water jet
(in particular high-pressure water jet).
The airflow slots must always be clean.
1. Clean the airflow slots
2. Clean all movable parts after each operation. Especially remove any
grass and dirt from the cover
To replace the filament cassette [ Fig. M2/M3 ]:
DANGER! Risk of injury!
Risk of injury from metal cutting parts!
v Do not use metal cutting parts or replacement parts and
accessories not approved by GARDENA.
Only use original GARDENA Filament Cassettes.
You can order Replacement Filament Cassettes from your
GARDENA dealer or directly from the GARDENA Customer Service.
For Art. 9805 SmallCut 300 / Art. 9806 SmallCut Plus 350:
GARDENA Filament Cassette for Turbotrimmers Art. 5307.
1. Push in cassette cover
and remove.
6
2. Remove the filament cassette
3. Remove all dirt.
4. Pull approximately 15 cm of the cutting filament
7
and
filament cassette
5. First put the cutting filament
6. Put the cutting filament
7. Put the filament cassette
8. Attach the cassette cover
you hear both locking clips
When attaching the cassette cover
put around the guide pin
v If the cassette cover
cassette
t
back and forth, until the filament cassette
filament cassette holder
5. STORAGE
To put into storage:
The product must be stored away from children.
1. Disconnect the mains cable.
2. Clean the product (see 4. MAINTENANCE).
3. Stow the product in a dry area where it has protection from frost.
Recommendation:
The product can be hung up by the handle. The cutting head is not put
under too much strain if the product is stowed hanging up.
Disposal:
(in accordance with RL2012/19/EC / S.I. 2013 No. 3113)
The product must not be disposed of to normal household
waste. It must be disposed of in line with local environmental
regulations.
IMPORTANT!
v Dispose of the product through or via your municipal recycling
collection centre.
w
with a soft brush (do not use a screwdriver).
4
.
e
on the two locking clips
t
.
5
t
through the hole in the plastic ring
5
through the metal sleeve
5
i
around the guide pin
.
t
into the filament cassette holder
e
on the filament cassette holder
r
make a click.
e
, the cutting filament
i
and must not be caught.
e
cannot be fully installed, turn the filament
o
.
r
at the same time
out of the new
z
.
u
.
o
.
o
until
5
must be
t
is fully in the