Makita 6096D 사용 설명서 - 페이지 7
{카테고리_이름} Makita 6096D에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Makita 6096D 9 페이지. Cordless high speed drill equipped with electric brake
Makita 6096D에 대해서도 마찬가지입니다: 사용자 설명서 (5 페이지), 사용 설명서 (17 페이지), 사용 설명서 (13 페이지)
페이지 인쇄
counterclockwise.
OPERATION
Screwdriving operation
001725
CAUTION:
Adjust the adjusting ring to the proper torque level
•
for your work.
Place the point of the driver bit in the screw head and
apply pressure to the tool. Start the tool slowly and then
increase the speed gradually. Release the switch trigger
as soon as the clutch cuts in.
CAUTION:
Make sure that the driver bit is inserted straight in
•
the screw head, or the screw and/or bit may be
damaged.
NOTE:
When driving wood screws, predrill pilot holes to
•
make driving easier and to prevent splitting of the
workpiece. See the chart.
Nominal diameter of wood screw
(mm)
3.1
3.5
3.8
4.5
4.8
5.1
5.5
006420
Drilling operation
First, turn the adjusting ring so that the pointer points to
the
marking. Then proceed as follows.
Drilling in wood
When drilling in wood, the best results are obtained with
wood drills equipped with a guide screw. The guide
screw makes drilling easier by pulling the bit into the
workpiece.
Drilling in metal
To prevent the bit from slipping when starting a hole,
make an indentation with a center-punch and hammer at
the point to be drilled. Place the point of the bit in the
indentation and start drilling.
Recommended size of pilot hole
(mm)
2.0 - 2.2
2.2 - 2.5
2.5 - 2.8
2.9 - 3.2
3.1 - 3.4
3.3 - 3.6
3.7 - 3.9
Use a cutting lubricant when drilling metals. The
exceptions are iron and brass which should be drilled
dry.
CAUTION:
Pressing excessively on the tool will not speed up
•
the drilling. In fact, this excessive pressure will only
serve to damage the tip of your bit, decrease the
tool performance and shorten the service life of the
tool.
There is a tremendous force exerted on the tool/bit
•
at the time of hole break through. Hold the tool
firmly and exert care when the bit begins to break
through the workpiece.
A stuck bit can be removed simply by setting the
•
reversing switch to reverse rotation in order to back
out. However, the tool may back out abruptly if you
do not hold it firmly.
Always secure small workpieces in a vise or similar
•
hold-down device.
If the tool is operated continuously until the battery
•
cartridge has discharged, allow the tool to rest for
15 minutes before proceeding with a fresh battery.
MAINTENANCE
CAUTION:
Always be sure that the tool is switched off and the
•
battery cartridge is removed before attempting to
perform inspection or maintenance.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers,
always using Makita replacement parts.
ACCESSORIES
CAUTION:
These
accessories
•
recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to
persons.
attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
Drill bits
•
Screw bits
•
Various type of Makita genuine batteries and
•
chargers
Set plate
•
Rubber pad assembly
•
Wool bonnet
•
Foam polishing pad
•
7
or
attachments
Only use
accessory or
are