Gardena 9334 운영자 매뉴얼 - 페이지 6

{카테고리_이름} Gardena 9334에 대한 운영자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Gardena 9334 8 페이지. Electric blower/vac
Gardena 9334에 대해서도 마찬가지입니다: 사용 설명서 (9 페이지)

페이지 인쇄

Connecting the unit [ Fig. O1 / O2 ]:

CAUTION! To avoid damage to the plug, the extension cable must be

inserted into the cable lock.

1. First make a loop with the extension cable

cable lock

and pull the extension cable tight.

2. Connect the unit's plug to the extension cable.

3. Connect the extension cable to a 230-V mains socket.

Starting the unit [ Fig. O3 ]:

To start:

to the ON position.

v Move the ON/OFF switch

The unit starts.

NOTE: For ErgoJet 3000 (EJ 3000) only: The motor speed can be

increased or decreased by using the variable speed control

WARNING! To avoid causing damage to the unit, only use the variable

speed control in blow mode. DO NOT attempt to use the variable speed

control in vacuum mode. Lower speeds during vacuum use could allow

debris to build up, stall the motor and cause unit failure.

To stop:

to the OFF position.

v Move the ON/OFF switch

The unit stops.

Work positions:

Blow mode [ Fig. O4 ]:

Use your unit as a blower for sweeping debris or grass clippings from

driveways, sidewalks, patios, etc. Also, for blowing grass clippings, straw,

or leaves into piles, or removing debris from corners, around joints, or

between bricks.

For ErgoJet 3000 (EJ 3000) only:

Use the variable speed control to increase or decrease the motor speed

during blower use.

Direct air flow by directing the blower tube down or to one side.

Always work away from solid objects such as walks, large stones, vehicles,

and fences.

Clean corners by starting in corners and moving outward. This will help

prevent an accumulation of debris which could fly into your face. Be careful

when working near plants. The force of the air could damage tender plants.

Vacuum mode [ Fig. O5 ]:

Use your unit as a vacuum to pick up dry material such as leaves, grass,

small twigs, and bits of paper.

For best results during vacuum use, operate your unit at high speed.

Move slowly back and forth over the material as you vacuum. Avoid forcing

the unit into a pile of debris as this can clog the unit.

Keep the vacuum tube about an inch above the ground for best results.

WARNING! If the unit becomes clogged, stop the unit and

unplug the extension cord. Wait until the impeller has

completely stopped turning, then remove the vacuum

tubes. Carefully reach into the vacuum opening and clear out the

clogged debris.

This will reduce possible personal injury from the impeller.

4. STORAGE

To put into storage:

Store unit unplugged, well out of the reach of children.

1. Stop unit and disconnect from the mains electricity supply.

2. Allow motor to cool before storing or transporting.

3. Store unit with all guards in place. Position unit so that any sharp object

cannot accidentally cause injury.

Extended storage:

Prepare unit for storage at the end of the season or if it will not be used for

30 days or more.

If your blower is to be stored for a period of time:

1. Stop unit and disconnect from the mains electricity supply.

2. Clean the entire unit before lengthy storage.

3. Open inlet cover and clean any dirt, grass, or debris that has collected.

Inspect the blower and all tubes. Close and make sure the cover is

latched.

, thread the loop into the

4. Use a soft brush to clean air vents and air inlet of debris. Do not use

water.

5. Store your unit and extension cord in a well ventilated area and covered,

if possible, to prevent dust and dirt accumulation. Do not cover with

plastic. Plastic cannot breathe and may cause condensation and even-

tual rust or corrosion.

6. Check entire unit for loose screws. Replace any damaged, worn, or

broken parts.

7. Remove tube(s) for easier storage.

Disposal:

(in accordance with RL2012/19/EC / S.I. 2013 No. 3113)

The product must not be disposed of to normal household

waste. It must be disposed of in line with local environmental

regulations.

IMPORTANT!

v Dispose of the product through or via your municipal recycling

collection centre.

5. MAINTENANCE

WARNING! Stop the unit and disconnect the plug from the

power source before making any adjustments, changing

accessories, or performing maintenance.

Such preventive safety measures reduce the risk of starting the power

tool accidentally.

BEFORE EACH USE

Check for loose fasteners and parts:

Keep all nuts, bolts and screws tight to be sure the product is in a safe

working condition. Be sure all parts are assembled properly.

• Inlet Cover

• Blower Tube

• Vacuum Tubes

• Collection Bag

Check for damaged or worn parts:

Contact your authorized service dealer for replacement of damaged or

worn parts.

• ON/OFF Switch – Ensure switch functions properly by moving the

switch to the OFF position. Make sure motor stops; then restart motor

and continue.

• Inlet Cover – Discontinue use of unit if inlet cover fails to latch properly

or if it is damaged in any way.

AFTER EACH USE

Inspect and clean unit and labels:

DANGER!

Electric shock!

Never clean the ventilation slit with a metal object.

• After each use, inspect complete unit for loose or damaged parts.

Clean the unit using a damp cloth.

• Wipe off unit with a clean dry cloth.

Clean collection bag:

IMPORTANT!

THE COLLECTION BAG MUST BE PROPERLY EMPTIED.

• You must properly empty and maintain the collection bag to avoid dete-

rioration and obstruction of air flow.

• Remove the collection bag from the unit and empty after each use. Do not

store bag without emptying the bag of all contents (grass, leaves, etc.).

• Wash the bag once a year. Remove the bag from the blower and turn

the bag inside out. Wash the bag with a water hose. Allow the bag to

hang and dry completely before you reuse the bag.