Garmin APPROACH S62 소유자 매뉴얼 - 페이지 18
{카테고리_이름} Garmin APPROACH S62에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin APPROACH S62 24 페이지.
Garmin APPROACH S62에 대해서도 마찬가지입니다: 소유자 매뉴얼 (24 페이지)
페이지 인쇄
USB Mode: Sets the device to use MTP (media transfer
protocol) or Garmin mode when connected to a computer.
Garmin mode allows you to continue using the device while it
is plugged in to a power source.
Wireless Sensors
Your device can be used with wireless ANT+ or Bluetooth
sensors. For more information about compatibility and
purchasing optional sensors, go to buy.garmin.com.
Pairing Your Wireless Sensors
The first time you connect a wireless ANT+ or Bluetooth sensor
to your Garmin device, you must pair the device and sensor.
After they are paired, the device connects to the sensor
automatically when you start an activity and the sensor is active
and within range.
TIP: Some ANT+ sensors pair with your device automatically
when you start an activity with the sensor turned on and near
the device.
1
Move at least 10 m (33 ft.) away from other wireless sensors.
2
If you are pairing a heart rate monitor, put on the heart rate
monitor.
The heart rate monitor does not send or receive data until
you put it on.
3
Press Menu.
4
Select Settings > Sensors & Accessories.
5
Select an option:
• To pair a club sensor, select Club Sensors > Add New.
• To pair a different sensor, select Add New, and select the
sensor type.
6
Bring the device within 3 m (10 ft.) of the sensor, and wait
while the device pairs with the sensor.
After the device connects to the sensor, an icon appears at
the top of the screen.
Club Sensors
Your device is compatible with Approach CT10 golf club
sensors. You can use paired club sensors to automatically track
your golf shots, including location, distance, and club type. See
the owner's manual for your club sensors for more information
(garmin.com/manuals/ApproachCT10).
Using an Optional Bike Speed or Cadence
Sensor
You can use a compatible bike speed or cadence sensor to
send data to your device.
• Pair the sensor with your device
page
14).
• Set your wheel size
(Wheel Size and Circumference,
page
18).
• Go for a ride
(Starting an Activity, page
Foot Pod
Your device is compatible with the foot pod. You can use the
foot pod to record pace and distance instead of using GPS when
you are training indoors or when your GPS signal is weak. The
foot pod is on standby and ready to send data (like the heart
rate monitor).
After 30 minutes of inactivity, the foot pod powers off to
conserve the battery. When the battery is low, a message
appears on your device. Approximately five hours of battery life
remain.
14
(Wireless Sensors,
10).
Improving Foot Pod Calibration
Before you can calibrate your device, you must acquire GPS
signals and pair your device with the foot pod
Sensors, page
14).
The foot pod is self-calibrating, but you can improve the
accuracy of the speed and distance data with a few outdoor runs
using GPS.
1
Stand outside for 5 minutes with a clear view of the sky.
2
Start a running activity.
3
Run on a track without stopping for 10 minutes.
4
Stop your activity, and save it.
Based on the recorded data, the foot pod calibration value
changes, if necessary. You should not need to calibrate the
foot pod again unless your running style changes.
tempe
™
The tempe is an ANT+ wireless temperature sensor. You can
attach the sensor to a secure strap or loop where it is exposed
to ambient air, and therefore, provides a consistent source of
accurate temperature data. You must pair the tempe with your
device to display temperature data from the tempe.
Device Information
Changing the QuickFit
1
Slide the latch on the QuickFit band, and remove the band
from the watch.
2
Align the new band with the watch.
3
Press the band into place.
NOTE: Make sure the band is secure. The latch should close
over the watch pin.
4
Repeat steps 1 through 3 to change the other band.
Specifications
Battery type
Battery life
Water rating
Operating temperature range From -20º to 55ºC (from -4º to 131ºF)
Charging temperature range
Wireless frequencies/
protocols
Device Care
Avoid extreme shock and harsh treatment, because it can
degrade the life of the product.
Avoid pressing the keys under water.
Do not use a sharp object to clean the device.
Never use a hard or sharp object to operate the touchscreen, or
damage may result.
1
The device withstands pressure equivalent to a depth of 50 m. For more
information, go to www.garmin.com/waterrating.
(Wireless
Bands
®
Rechargeable, built-in lithium-ion battery
Up to 14 days in smartwatch mode
Up to 20 hours in GPS mode
1
5 ATM
From 0º to 45ºC (from 32º to 113ºF)
2.4 GHz @ 3.2 dBm nominal
13.56 MHz @ -40 dBm nominal
NOTICE
Wireless Sensors