Garmin quatix 3 소유자 매뉴얼 - 페이지 23

{카테고리_이름} Garmin quatix 3에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin quatix 3 34 페이지.

페이지 인쇄

The foot pod is self-calibrating, but you can improve the

accuracy of the speed and distance data with a few outdoor runs

using GPS.

Stand outside for 5 minutes with a clear view of the sky.

Start a running activity.

Run on a track without stopping for 10 minutes.

Stop your activity, and save it.

Based on the recorded data, the foot pod calibration value

changes, if necessary. You should not need to calibrate the

foot pod again unless your running style changes.

Calibrating Your Foot Pod Manually

Before you can calibrate your device, you must pair your device

with the foot pod sensor

(Pairing ANT+ Sensors, page

Manual calibration is recommended if you know your calibration

factor. If you have calibrated a foot pod with another Garmin

product, you may know your calibration factor.

Hold UP.

Select Settings > Sensors.

Select your foot pod.

Select Cal. Factor > Set Value.

Adjust the calibration factor:

• Increase the calibration factor if your distance is too low.

• Decrease the calibration factor if your distance is too high.

Setting Foot Pod Speed and Distance

Before you can customize the foot pod speed and distance, you

must pair your device with the foot pod sensor

Sensors, page

18).

You can set your device to calculate pace and distance from

your foot pod data instead of GPS data.

Hold UP.

Select Settings > Sensors.

Select your foot pod.

Select Speed.

Select an option:

• Select Indoor when you are training with GPS turned off,

usually indoors.

• Select Always to use your foot pod data regardless of the

GPS setting.

tempe

The tempe is an ANT+ wireless temperature sensor. You can

attach the sensor to a secure strap or loop where it is exposed

to ambient air, and therefore, provides a consistent source of

accurate temperature data. You must pair the tempe with your

device to display temperature data from the tempe.

Running Dynamics

You can use your compatible quatix 3 device paired with the

quatix 3 accessory to provide real-time feedback about your

Color Gauges and Running Dynamics Data

The running dynamics screens display a color gauge for the primary metric. You can display cadence, vertical oscillation, ground

contact time, ground contact time balance, or vertical ratio as the primary metric. The color gauge shows you how your running

dynamics data compare to those of other runners. The color zones are based on percentiles.

Garmin has researched many runners of all different levels. The data values in the red or orange zones are typical for less

experienced or slower runners. The data values in the green, blue, or purple zones are typical for more experienced or faster

runners. More experienced runners tend to exhibit shorter ground contact times, lower vertical oscillation, lower vertical ratio, and

higher cadence than less experienced runners. However, taller runners typically have slightly slower cadences, longer strides, and

slightly higher vertical oscillation. Vertical ratio is your vertical oscillation divided by stride length. It is not correlated with height.

NOTE: The color gauge for ground contact time balance is different

Go to

www.garmin.com

for more information on running dynamics. For additional theories and interpretations of running dynamics

data, you can search reputable running publications and websites.

ANT+ Sensors

running form. If your quatix 3 device was packaged with the

quatix 3 accessory, the devices are already paired.

The quatix 3 accessory has an accelerometer in the module that

measures torso movement in order to calculate six running

metrics.

Cadence: Cadence is the number of steps per minute. It

displays the total steps (right and left combined).

Vertical oscillation: Vertical oscillation is your bounce while

running. It displays the vertical motion of your torso,

measured in centimeters for each step.

Ground contact time: Ground contact time is the amount of

time in each step that you spend on the ground while

running. It is measured in milliseconds.

18).

NOTE: Ground contact time is not available while walking.

Ground contact time balance: Ground contact time balance

displays the left/right balance of your ground contact time

while running. It displays a percentage. For example, 53.2

with an arrow pointing left or right.

Stride length: Stride length is the length of your stride from one

footfall to the next. It is measured in meters.

Vertical ratio: Vertical ratio is the ratio of vertical oscillation to

stride length. It displays a percentage. A lower number

typically indicates better running form.

Training with Running Dynamics

Before you can view running dynamics, you must put on the

HRM-Run accessory and pair it with your device

Sensors, page

accessory, the devices are already paired, and the quatix 3 is

(Pairing ANT+

set to display running dynamics.

Select an option:

• If your HRM-Run accessory and quatix 3 device are

• If your HRM-Run accessory and quatix 3 device are not

Hold UP.

Select Settings > Apps.

Select an activity.

Select Data Screens.

Select a running dynamics data screen.

NOTE: The running dynamics screens are not available for

all activities.

Select Status > Enabled.

Go for a run

Select UP or DOWN to open a running dynamics screen to

view your metrics.

(Ground Contact Time Balance Data, page

18). If your quatix 3 was packaged with the

already paired, skip to step 8.

already paired, complete all the steps in this procedure.

(Going for a Run, page

(Pairing ANT+

4).

20).