Garmin Vivoactive 4 소유자 매뉴얼 - 페이지 30
{카테고리_이름} Garmin Vivoactive 4에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin Vivoactive 4 38 페이지. Turn on smart watch of 2022 - go wiki
Garmin Vivoactive 4에 대해서도 마찬가지입니다: 소유자 매뉴얼 (29 페이지), 방법 (8 페이지)
페이지 인쇄
3 Press
to start the timer.
4 Press
to restart the lap timer.
The total stopwatch time continues running.
5 Select
to stop the timer.
6 Select an option:
• To reset the timer, swipe down.
• To save the stopwatch time as an activity, press
, and select
.
• To exit the stopwatch, press
Backlight Settings
Hold
, and select
> System > Display.
Mode: Sets the backlight to turn on when you interact
with the device, which includes receiving a
notification or using the buttons or touchscreen.
Brightness: Sets the brightness level of the backlight.
Timeout: Sets the length of time before the backlight
turns off.
Gesture: Sets the backlight to turn on when you rotate
your wrist toward your body to view the device.
You can use the Only During Activity option to use
this feature only during timed activities. You can
also adjust the gesture sensitivity to turn on the
backlight more or less often.
Changing the Units of Measure
You can customize units of measure for distance, pace
and speed, elevation, weight, height, and temperature.
1 From the watch face. hold
2 Select
> System > Units.
3 Select a measurement type.
4 Select a unit of measure.
Garmin Connect Settings
You can change your device settings from your Garmin
Connect account, using either the Garmin Connect
app or the Garmin Connect website. Some settings are
available only using your Garmin Connect account and
cannot be changed on your device.
y From the Garmin Connect app, select
select Garmin Devices, and select your device.
y From the devices widget in the Garmin Connect
application, select your device.
After customizing settings, sync your data to apply
the changes to your device
App,
page 20,
Using Garmin Connect on Your Computer,
page 20).
Wireless Sensors
Your device can be used with wireless ANT+ or
Bluetooth sensors. For more information about
compatibility and purchasing optional sensors, go to
Garmin.com.sg/buy.
Wireless Sensors
, and select
.
or
,
(Using the Garmin Connect
Pairing Your Wireless Sensors
The first time you connect a wireless ANT+ or
Bluetooth sensor to your Garmin device, you must pair
the device and sensor. After they are paired, the device
connects to the sensor automatically when you start
an activity and the sensor is active and within range.
TIP: Some ANT+ sensors pair with your device
automatically when you start an activity with the
sensor turned on and near the device.
.
1 Move at least 10 m (33 ft.) away from other
wireless sensors.
2 If you are pairing a heart rate monitor, put on the
heart rate monitor.
The heart rate monitor does not send or receive
data until you put it on.
3 Hold
.
4 Select
> Sensors > Add New.
5 Bring the device within 3 m (10 ft.) of the sensor,
and wait while the device pairs with the sensor.
After the device connects to the sensor, an icon
appears at the top of the screen.
Foot Pod
Your device is compatible with the foot pod. You can
use the foot pod to record pace and distance instead
of using GPS when you are training indoors or when
your GPS signal is weak. The foot pod is on standby
and ready to send data (like the heart rate monitor).
After 30 minutes of inactivity, the foot pod powers
off to conserve the battery. When the battery is low, a
message appears on your device. Approximately five
hours of battery life remain.
Calibrating Your Foot Pod
Before you can calibrate your foot pod, you must pair
your device with the foot pod
Sensors,
page 25).
Manual calibration is recommended if you know your
calibration factor. If you have calibrated a foot pod
with another Garmin product, you may know your
calibration factor.
1 Hold
.
2 Select
> Sensors > Foot Pod > Calib� Factor.
3 Adjust the calibration factor:
• Increase the calibration factor if your distance is
too low.
• Decrease the calibration factor if your distance
is too high.
Improving Foot Pod Calibration
Before you can calibrate your device, you must acquire
GPS signals and pair your device with the foot pod
(Pairing Your Wireless Sensors,
The foot pod is self-calibrating, but you can improve
the accuracy of the speed and distance data with a
(Pairing Your Wireless
page 25).
25