Garmin GPSMAP 2006 설치 지침 매뉴얼 - 페이지 5

{카테고리_이름} Garmin GPSMAP 2006에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GPSMAP 2006 12 페이지. Garmin gsd 20 marine-remote sounder: release note
Garmin GPSMAP 2006에 대해서도 마찬가지입니다: 적합성 선언 (1 페이지), 설치 매뉴얼 (2 페이지), 적합성 선언 (1 페이지), 설치 매뉴얼 (8 페이지), 소유자 매뉴얼 (20 페이지)

페이지 인쇄

Flush Mount

Tools

• Flush Mount Template

• Jig saw

• Masking tape

• Scissors

• Drill

• Drill bits—1/8" (3 mm) and 3/8" (6 mm)

• 1/16" (2 mm) Allen (Hex) wrench

• Sockets or wrenches

• Hammer

• Center punch

To ﬂush mount the GPSMAP 2006C/2010C:

1. Trim the Flush Mount Template and tape it in the location you want.

2. Using the center punch, indent the center of each mounting hole location.

3. Using an 1/8" (3 mm) drill bit, drill the four mounting holes.

4. Using a 3/8" (6 mm) drill bit, drill a hole for a location to begin cutting the mounting surface.

5. Using the Jig Saw, cut the mounting surface along the inside of the dashed line indicated on the template. Use a ﬁle and sandpaper to

reﬁne the size of the hole. Be very careful when cutting this hole. There is only a small amount of clearance between the case

molding and the mounting holes.

6. Install the four mounting studs into unit by screwing the shorter, threaded section into the back of the unit. Use a 1/16" (2 mm) Allen

wrench to tighten the mounting studs until the stop contacts the case. Be careful not to overtighten as this may damage the

mounting stud! The studs have a reusable thread-locking patch

pre-applied from the factory.

7. Place the unit in position in the cut-out of the mounting surface.

8. Place washers over the mounting studs, then thread on one

hex nut per mounting stud. Tighten all four until the unit is snug

against the mounting surface. Install and tighten the second hex

nut set on all four mounting studs to lock the ﬁrst set in place.

TRIM TEMPLATE ALONG THIS LINE TO AID FITTING

230mm

GPSMAP 2010/2010C/3010C

CUT MOUNTING SURFACE

ALONG INSIDE OF THIS LINE

Be very careful when cutting this hole,

there is only a small amount of clearance

between the unit and the Mounting Hole.

Flush Mounting the GPS

1. Trim the Flush Mount Template and tape in the desired location.

2. Using the Center Punch, indent the center of each Mounting Hole location.

3. Using an 1/8" (3mm) drill bit, drill the four Mounting Holes. (Drilling the mounting

holes before cutting the hole for the unit will allow for an easier installation.)

4. Using a 3/8" (6mm) drill bit, drill a hole for a location to begin cutting the mounting

UNIT OUTLINE

surface.

5. Using the Jig Saw, cut the mounting surface along the inside of the dashed line

indicated on the template. Be very careful when cutting this hole, there is only a small

amount of clearance between the case molding and the Mounting Holes.

6. Install the four Mounting Studs into unit by screwing the shorter, threaded section

into the back of the unit. Use a 1/16" (2mm) Allen Wrench to tighten the Mounting Studs

until the stop contacts the case. Be careful not to overtighten as this may damage the

Mounting Stud! The studs have a reusable thread-locking patch pre-applied from the factory.

7. Place the unit in position in the cut out of the mounting surface.

8. Place washers over the Mounting Studs, then thread on one Hex Nut per Mounting Stud.

Tighten all four until the unit is snug against the mounting surface.

Install and tighten the second Hex Nut on all four Mounting Studs to lock the first one

in place.

DRILL A 3/8" HOLE.

BEGIN CUTTING HERE

Flush Mount Template

GPSMAP 2006C/2010C & GPS 17

208mm

Flush Mount

Stud

Washer Hex nuts

NSTALLATION

NSTRUCTIONS

Mounting surface