Garmin GPSMAP 800 Series 설치 지침 매뉴얼

{카테고리_이름} Garmin GPSMAP 800 Series에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GPSMAP 800 Series 6 페이지. Flat-mount kit
Garmin GPSMAP 800 Series에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (17 페이지), 파일럿 매뉴얼 부록 (22 페이지), 소유자 매뉴얼 (40 페이지), 빠른 시작 매뉴얼 (4 페이지), 소유자 매뉴얼 (46 페이지), 운영자 매뉴얼 (32 페이지), 설치 지침 매뉴얼 (34 페이지), 설치 지침 매뉴얼 (6 페이지)

페이지 인쇄

GPSMAP

800 and 1000 Series

Installation Instructions

Important Safety Information

See the Important Safety and Product Information guide in the

product box for product warnings and other important

information.

When connecting the power cable, do not remove the in-line

fuse holder. To prevent the possibility of injury or product

damage caused by fire or overheating, the appropriate fuse

must be in place as indicated in the product specifications. In

addition, connecting the power cable without the appropriate

fuse in place will void the product warranty.

Always wear safety goggles, ear protection, and a dust mask

when drilling, cutting, or sanding.

When drilling or cutting, always check what is on the opposite

side of the surface.

Registering Your Device

Help us better support you by completing our online registration

today.

• Go to http://my.garmin.com.

• Keep the original sales receipt, or a photocopy, in a safe

place.

Contacting Garmin Product Support

• Go to

www.garmin.com/support

for in-country support information.

• In the USA, call (913) 397.8200 or (800) 800.1020.

• In the UK, call 0808 2380000.

• In Europe, call +44 (0) 870.8501241.

Tools Needed

• Drill and drill bits

• #2 Phillips screwdriver

• Jigsaw or rotary tool

• File and sandpaper

• Marine sealant (optional)

Mounting Considerations

This device should be mounted in a location that is not exposed

to extreme temperatures or conditions. The temperature range

for this device is listed in the product specifications. Extended

exposure to temperatures exceeding the specified temperature

range, in storage or operating conditions, may cause device

failure. Extreme-temperature-induced damage and related

consequences are not covered by the warranty.

Using the included hardware and template, you can mount the

device using one of two methods. You can use the included

bracket and hardware to bail mount the device, or you can use

the included template and hardware to flush mount the device in

the dashboard.

November 2013

WARNING

CAUTION

NOTICE

and click Contact Support

NOTICE

When selecting a mounting location, you should observe these

considerations.

• The location should provide optimal viewing as you operate

your boat.

• The location should allow for easy access to all device

interfaces, such as the keypad, touchscreen, and card

reader, if applicable.

• The location must be strong enough to support the weight of

the device and protect it from excessive vibration or shock.

• To avoid interference with a magnetic compass, the device

should not be installed closer to a compass than the

compass-safe distance value listed in the product

specifications.

• The location must allow room for the routing and connection

of all cables.

Bail Mounting the Device

If you are mounting the bracket on fiberglass with screws, it is

recommended to use a countersink bit to drill a clearance

counterbore through only the top gel-coat layer. This will help to

avoid any cracking in the gel-coat layer when the screws are

tightened.

Stainless-steel screws may bind when screwed into fiberglass

and overtightened. Garmin

lubricant to the screws before installing them.

You can use the included bracket to bail mount the device on a

flat surface.

Using the bail-mount bracket

holes

Using a 3 mm (

Using the included screws

to the mounting surface.

Install the bail-mount knobs

Place the device in the bail-mount bracket and tighten the

bail-mount knobs.

Flush Mounting the Device

Be careful when cutting the hole to flush mount the device.

There is only a small amount of clearance between the case

and the mounting holes, and cutting the hole too large could

compromise the stability of the device after it is mounted.

If you are mounting the bracket on fiberglass with screws, it is

recommended to use a countersink bit to drill a clearance

counterbore through only the top gel-coat layer. This will help to

avoid any cracking in the gel-coat layer when the screws are

tightened.

190-01658-02_0A

NOTICE

recommends applying an anti-seize

as a template, mark the pilot

in.) drill bit, drill the pilot holes.

, secure the bail-mount bracket

on the sides of the device.

NOTICE

Printed in Taiwan