Brother 888X64 Series 운영 매뉴얼 - 페이지 36

{카테고리_이름} Brother 888X64 Series에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Brother 888X64 Series 48 페이지.
Brother 888X64 Series에 대해서도 마찬가지입니다: 운영 매뉴얼 (2 페이지), 운영 매뉴얼 (47 페이지), 운영 매뉴얼 (2 페이지), 운영 매뉴얼 (48 페이지), 운영 매뉴얼 (3 페이지)

페이지 인쇄

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

Step

Step 3

(Back bar tack)

1. Turn the pattern selection dial to "c" (same

position as in step 1).

2. Sew 5 to 6 stitches.

3. Stop the machine when the needle is at the right

side of the stitch and then raise the needle from the

material.

Step 4

(Right side)

1. Set the pattern selection dial to "d".

2. Sew the right side until the needle reaches the

stitches sewn in step 1.

■ Securing the Stitching and Cutting the

Buttonhole

To secure the stitching, turn the material

90 degrees counterclockwise and sew

straight stitches to the end of the front bar

tack of the buttonhole.

Remove the material from the machine.

We recommend that you put pins across

both ends of the buttonhole to prevent the

stitches from being cut.

Cut an opening in the middle of the

buttonhole with the seam ripper tool. Be

careful not to cut through any stitches.

CAUTION

●

When using the seam ripper to open the

buttonhole, do not put your hand or

finger in the path of the ripper. The seam

ripper may slip and you may be injured.

Sewn section

Pattern

Adjusting buttonholes

If the stitching on the two sides of the buttonhole is not

the same, you can make the following adjustments.

After sewing the left side of the

buttonhole, stitch the right side and

observe the feeding.

1 Right row

If the left side is too open or tight

compared with the right side, adjust the

buttonhole fine-adjustment screw as

described in the following paragraphs.

1 Buttonhole fine-adjustment screw

2 Left side

3 Buttonhole appearance

If the left side is too open, turn the buttonhole

fine-adjustment screw with a large

screwdriver in the

If the left side is too tight, turn the buttonhole

fine-adjustment screw with a large

screwdriver in the

• This adjustment ensures both sides of the

buttonhole are the same.

"–"

direction.

"+"

direction.