Garmin GNS 530A 빠른 참조 - 페이지 3

{카테고리_이름} Garmin GNS 530A에 대한 빠른 참조을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GNS 530A 23 페이지. 500 series
Garmin GNS 530A에 대해서도 마찬가지입니다: 사용 설명서 (6 페이지), 파일럿 매뉴얼 부록 (27 페이지), 파일럿 매뉴얼 부록 (4 페이지), 파일럿 매뉴얼 부록 (22 페이지), 설치 매뉴얼 (14 페이지)

페이지 인쇄

1. Left-Hand Keys and Knobs

(11) ENT Key – Used to approve an operation or complete

data entry. It is also used to confirm information during

power on.

(12) Small Right Knob – Used to select pages within

the page groups. Press this knob momentarily to display

the on-screen cursor. The cursor allows the pilot to enter

data and/or make a selection from a list of options. When

entering data, the small right knob is used to select the

desired letter or number and the large right knob is used

to move to the next character space. The small right knob

is also used to move the target pointer up (turn clockwise)

or down (counterclockwise) when the map panning

function is active.

(13) Large Right knob – Used to select page groups:

NAV, WPT, AUX, or NRST. With the on-screen cursor

enabled, the large right knob allows the pilot to move

the cursor about the page. The large right knob is also

used to move the target pointer right (turn clockwise) or

left (counterclockwise) when the map panning function

is active.

bottom Row KeyS

(14) CDI Key – Used to toggle which navigation source

(GPS or VLOC) provides output to an external HSI or

CDI.

(15) OBS Key – Used to select manual or automatic

sequencing of waypoints. Pressing the OBS Key selects

OBS mode, which retains the current 'active to' waypoint

as the navigation reference even after passing the waypoint

(i.e., prevents sequencing to the next waypoint). Pressing

the OBS Key again returns the unit to normal operation,

with automatic sequencing of waypoints. When OBS

mode is selected, the pilot may set the desired course

to/from a waypoint using the Select OBS Course pop-up

window, or an external OBS selector on the HSI or CDI.

190-00181-01 Rev. G

(16) MSG Key – Used to view system messages and to

alert the pilot to important warnings and requirements.

(17) FPL Key – Allows the pilot to create, edit, activate,

and invert flight plans, as well as access approaches,

departures, and arrivals. A closest point to flight plan

feature is also available from the FPL Key. See pages 17

and 18 for more information on flight plans.

(18) VNAV (Vertical Navigation) Key – Allows the

pilot to create a three-dimensional profile which provides

guidance to a final (target) altitude at a specified location.

(19) PROC Key – Allows the pilot to select and remove

approaches, departures, and arrivals from the flight plan.

When using a flight plan, available procedures for the

departure and/or arrival airport are offered automatically.

Otherwise, the pilot may select the desired airport, then

the desired procedure.

Powering on the GNS 530

Turn the COM Power/Volume Knob clockwise

to turn the unit power on and set the desired

radio volume.

A welcome page appears briefly while the unit

performs a self test, followed sequentially by the

Unit Type Page and the Software Version Page.

Then (depending on configuration) the Weather

Page, the Traffic Page, the Aviation Database

Page, and the Land/Terrain/Obstacles Database

Page are sequentially displayed.

Once the self-test concludes, the Database

Versions Page appears which shows the current

database information on the NavData® Card

and Terrain Data Cards. Press the ENT Key

to acknowledge the Database Versions Page

and proceed to the Instrument Panel Self-test

Page.

GNS 530(A) Quick Reference

KEYS AND KNOBS