Garmin echomap 50 series 설치 지침 매뉴얼 - 페이지 3
{카테고리_이름} Garmin echomap 50 series에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin echomap 50 series 6 페이지. Flat-mount kit
Garmin echomap 50 series에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (4 페이지), 소유자 매뉴얼 (38 페이지), 소유자 매뉴얼 (44 페이지), 소유자 매뉴얼 (30 페이지), 설치 지침 매뉴얼 (6 페이지), 소유자 매뉴얼 (50 페이지), 설치 지침 매뉴얼 (34 페이지)
페이지 인쇄
5
Using the appropriate drill bit for the hardware, drill the three
pilot holes.
6
5
Using a
/
in. (16 mm) drill, drill a cable routing hole through
8
the mounting surface at the location you marked in step 4.
Fastening the Swivel Mount without the Cables
Running through the Mount
You should complete this procedure only if you are not running
the power and transducer cables under the mounting surface
and through the swivel-mount base.
1
Place the base
on the mounting surface, and fasten it
using the appropriate screws or bolts
2
Place the swivel mount on the base, and replace the 10 mm
M6×1 Phillips screw.
3
Seal the cable pass-through holes with marine sealant.
Fastening the Swivel Mount with the Cables Running
through the Mount
You should complete this procedure only when running the
power and transducer cables under the mounting surface and
through the swivel-mount base.
1
Feed the cables through the 16 mm (
drilled when preparing to run cables beneath the mounting
surface.
2
Place the base on the mounting surface.
3
Route the cables through the cable pass-through holes.
4
Loosely fasten the base using the appropriate screws or
bolts.
5
Place the swivel mount on the base, but do not fasten it.
6
Place the cradle or device into the swivel mount
the Device in the Cradle, page
7
Pull out enough slack from the power and transducer cables
so the mount can fully swivel to the desired positions when
the cables are connected.
8
Remove the cradle and the swivel mount from the base.
9
Apply marine sealant to the 16 mm (
the cable pass-through holes.
10
Securely fasten the base with the appropriate screws or
bolts.
11
Place the swivel mount on the base, and fasten it using the
included 10 mm M6×1 Phillips screw.
.
5
/
in.) center hole you
8
(Installing
4).
5
/
in.) center hole and to
8
Installing the Cradle in the Mount
1
Pull up the locking arm
2
Place the cradle into the swivel mount
3
Tilt the mount to the desired viewing angle.
4
Press down the locking arm.
Installing the Cables and Connectors
Wiring to Power
1
Route the power cable from the mount to the boat battery or
fuse block.
2
If necessary, extend the wires using 0.82 mm
larger wire.
3
Connect the red wire to the positive terminal on the battery or
fuse block, and connect the black wire to the negative
terminal.
Connecting the Device to a Transducer
1
Follow the instructions provided with your transducer to
correctly install it on your boat.
2
Route the transducer cable to the back of your device, away
from sources of electrical interference.
3
Connect the transducer cable to the appropriate port on the
cradle.
Connecting the Cables to the Cradle
The connectors on the cables are keyed to fit in only in the
correct ports on the cradle. The connected cables are held in
place by a locking bracket.
1
Slide the cable locking bracket up from the bottom and
remove the bracket from the cradle.
2
Compare the divots
on each cable connector to the keying
on each port to determine which cable corresponds to each
port.
3
Fully and firmly insert each cable through a hole in the cradle,
and securely connect each cable to a port.
NOTE: If the cables are not inserted far enough into the
cradle, the connectors may not connect securely to the ports,
and the device may appear to lose power or stop working.
4
Place the locking bracket
bracket down to lock the cables in place.
.
.
2
(18 AWG) or
over the cables and slide the
3