Garmin ECHOMAP 70 Series 소유자 매뉴얼 - 페이지 12

{카테고리_이름} Garmin ECHOMAP 70 Series에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin ECHOMAP 70 Series 50 페이지. Flat-mount kit
Garmin ECHOMAP 70 Series에 대해서도 마찬가지입니다: 소유자 매뉴얼 (50 페이지), 빠른 시작 매뉴얼 (4 페이지), 소유자 매뉴얼 (38 페이지), 소유자 매뉴얼 (44 페이지), 소유자 매뉴얼 (30 페이지), 설치 지침 매뉴얼 (6 페이지), 설치 지침 (4 페이지), 설치 지침 (4 페이지), 설치 지침 매뉴얼 (34 페이지)

페이지 인쇄

• Select Photo Map Blend to show photos on both the

water and the land at a specified opacity. Use the slider

bar to adjust the photo opacity. The higher you set the

percentage, the more the satellite photos cover both land

and water.

Viewing Aerial Photos of Landmarks

Before you can view aerial photos on the Navigation chart, you

must turn on the Satellite Photos setting in the chart setup.

NOTE: This feature is available with premium charts, in some

areas.

You can use aerial photographs of landmarks, marinas, and

harbors to help orient yourself to your surroundings or to

acquaint yourself with a marina or a harbor prior to arrival.

From the Navigation chart, select a camera icon:

• To view an overhead photo, select

• To view a perspective photo, select

taken from the location of the camera, pointed in the

direction of the cone.

Select Aerial Photo.

Garmin Quickdraw

The Garmin Quickdraw Contours mapping feature allows you to

instantly create maps with contours and depth labels for any

body of water.

When Garmin Quickdraw Contours records data, a colored

circle surrounds the vessel icon. This circle represents the

approximate area of the map that is scanned by each pass. A

green circle indicates good depth and a good GPS position. A

red circle indicates that the depth or GPS position data is

unavailable.

You can view Garmin Quickdraw Contours in a combination

screen or as a single view on the map.

The amount of saved data depends on the size of your memory

card, your sonar source, and the speed of your boat as you

record data. You can record longer when you use a single-beam

sonar. It is estimated that you might be able to record about

1,500 hours of data onto a 2 GB memory card.

When you record data on a memory card in your chartplotter,

the new data is added to your existing Garmin Quickdraw

Contours map, and is saved on the memory card. When you

insert a new memory card, the existing data does not transfer

onto the new card.

Mapping a Body of Water Using the Garmin

Quickdraw Contours Feature

Before you can use the Garmin Quickdraw Contours feature,

you must have a supported chartplotter with upgraded software,

sonar depth, your GPS position, and a memory card with free

space.

NOTE: This feature is not available on all models.

From a chart view, select Menu > Quickdraw Contours >

Start Recording.

When recording is complete, select Stop Recording.

Select Manage > Name, and enter a name for the map.

Adding a Label to a Garmin Quickdraw Contours Map

You can add labels to a Garmin Quickdraw Contours map to

mark hazards or points of interest.

From the Navigation chart, select a location.

Select Add Quickdraw Label.

Enter text for the label, and select Done.

Garmin Quickdraw Contours Settings

From the chart, select Menu > Quickdraw Contours >

Settings.

. The photo was

Contours Mapping

™

Recording Offset: Sets the distance between the sonar depth

and the contour recording depth. For example, a sonar depth

of 3.6 m (12 ft.) with a recording offset of -0.5 m (-1.5 ft.)

creates contours at a depth of 3.1 m (10.5 ft.).

Display Offset: Sets differences in contour depths and depth

labels on a Garmin Quickdraw Contours map to compensate

for changes in the water level of a body of water, or for depth

errors in recorded maps.

Survey Coloring: Sets the color of the Garmin Quickdraw

Contours display. When the setting is turned on, successfully

recorded areas appear green, and unsuccessfully recorded

areas appear red. When the setting is turned off, the contour

areas use standard map colors.

Automatic Identification System

The Automatic Identification System (AIS) enables you to

identify and track other vessels, and alerts you to area traffic.

When connected to an external AIS device, the chartplotter can

show some AIS information about other vessels that are within

range, that are equipped with a transponder, and that are

actively transmitting AIS information.

The information reported for each vessel includes the Maritime

Mobile Service Identity (MMSI), location, GPS speed, GPS

heading, time that has elapsed since the last position of the

vessel was reported, nearest approach, and time to the nearest

approach.

Some chartplotter models also support Blue Force Tracking.

Vessels being tracked with Blue Force Tracking are indicated on

the chartplotter with a blue-green color.

AIS Targeting Symbols

Symbol Description

AIS vessel. The vessel is reporting AIS information. The

direction in which the triangle is pointing indicates the

direction in which the AIS vessel is moving.

Target is selected.

Target is activated. The target appears larger on the chart. A

green line attached to the target indicates the heading of the

target. The MMSI, speed, and direction of the vessel appear

beneath the target, if the details setting has been set to Show.

If the AIS transmission from the vessel is lost, a message

banner appears.

Target is lost. A green X indicates that the AIS transmission

from the vessel is lost, and the chartplotter displays a

message banner asking whether the vessel should continue

to be tracked. If you discontinue vessel tracking, the lost

target symbol disappears from the chart or the 3D chart view.

Dangerous target in range. The target flashes while an alarm

sounds and a message banner appears. After the alarm has

been acknowledged, a solid red triangle with a red line

attached to it indicates the location and the heading of the

target. If the safe-zone collision alarm has been set to Off, the

target flashes, but the audible alarm does not sound and the

alarm banner does not appear. If the AIS transmission from

the vessel is lost, a message banner appears.

Dangerous target is lost. A red X indicates that the AIS

transmission from the vessel is lost, and the chartplotter

displays a message banner asking whether the vessel should

continue to be tracked. If you discontinue vessel tracking, the

lost dangerous target symbol disappears from the chart or the

3D chart view.

The location of this symbol indicates the closest point of

approach to a dangerous target, and the numbers near the

symbol indicate the time to the closest point of approach to

that target.

NOTE: Vessels being tracked with the Blue Force Tracking

feature are indicated with a blue-green color regardless of their

status.

Charts and 3D Chart Views