Garmin ECHOMAP 70 Series 소유자 매뉴얼 - 페이지 31

{카테고리_이름} Garmin ECHOMAP 70 Series에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin ECHOMAP 70 Series 50 페이지. Flat-mount kit
Garmin ECHOMAP 70 Series에 대해서도 마찬가지입니다: 소유자 매뉴얼 (50 페이지), 빠른 시작 매뉴얼 (4 페이지), 소유자 매뉴얼 (38 페이지), 소유자 매뉴얼 (44 페이지), 소유자 매뉴얼 (30 페이지), 설치 지침 매뉴얼 (6 페이지), 설치 지침 (4 페이지), 설치 지침 (4 페이지), 설치 지침 매뉴얼 (34 페이지)

페이지 인쇄

Adjusting Sea Clutter on the Radar Screen Manually

You can adjust the appearance of clutter caused by choppy sea

conditions. The sea clutter setting affects the appearance of

nearby clutter and targets more than it affects the appearance of

distant clutter and targets. A higher sea clutter setting reduces

the appearance of clutter caused by nearby waves, but it can

also reduce or eliminate the appearance of nearby targets.

NOTE: Depending upon the radar in use, the sea clutter setting

configured for use in one radar mode may or may not be applied

to other radar modes or to the radar overlay.

From a radar screen or the radar overlay, select Menu >

Noise Rejection > Sea Clutter.

Select Up or Down to adjust the appearance of sea clutter

until other targets are clearly visible on the radar screen.

Clutter caused by sea conditions may still be visible.

Adjusting Rain Clutter on the Radar Screen

You can adjust the appearance of clutter caused by rain.

Reducing the radar range also can minimize rain clutter

(Adjusting the Zoom Scale on the Radar Screen, page

The rain clutter setting affects the appearance of nearby rain

clutter and targets more than it affects the appearance of distant

rain clutter and targets. A higher rain clutter setting reduces the

appearance of clutter caused by nearby rain, but it can also

reduce or eliminate the appearance of nearby targets.

NOTE: Depending upon the radar in use, the rain clutter settings

configured for use in one radar mode may or may not be applied

to other radar modes or to the Radar overlay.

From a Radar screen or the Radar overlay, select Menu >

Noise Rejection > Rain Clutter.

Select Up or Down to decrease or increase the appearance

of nearby rain clutter until other targets are clearly visible on

the Radar screen.

Clutter caused by rain may still be visible.

Reducing Cross Talk Clutter on the Radar Screen

You can reduce the appearance of clutter caused by

interference from another nearby radar source, when the cross

talk reject setting is on.

NOTE: Depending upon the radar in use, the cross talk reject

setting configured for use in one radar mode may or may not be

applied to other radar modes or to the Radar overlay.

From a Radar screen or the Radar overlay, select Menu >

Noise Rejection > Crosstalk Rej..

Echo Trails

The echo trails feature enables you to track the movement of

vessels on the radar display. You can change the length of time

the trail is displayed.

NOTE: Depending upon the radar in use, the settings configured

for use in one radar mode may or may not be applied to other

radar modes or to the radar overlay.

NOTE: Not all options and settings are available on all radar and

chartplotter models.

Turning on Echo Trails

From a radar screen or the radar overlay, select Menu >

Radar Setup > Echo Trails > Display.

Adjusting the Length of the Echo Trails

From a radar screen or the radar overlay, select Menu >

Radar Setup > Echo Trails > Time.

Select the length of the trail.

Clearing the Echo Trails

You can remove the echo trails from the radar screen to reduce

the clutter on the screen.

From a radar screen or the radar overlay, select Menu >

Radar Setup > Echo Trails > Clear Trails.

Gauges and Almanac Information

Radar Display Settings

From any Radar screen or the Radar overlay, select Menu >

Radar Setup.

Orientation: Sets the perspective of the radar display. The

orientation setting applies to every radar mode. This setting

does not apply to the Radar overlay.

Appearance: Sets the color scheme, look-ahead speed, and

navigation appearance.

Front of Boat: Compensates for the physical location of the

radar scanner on a boat, if the radar scanner does not align

with the bow-stern axis.

Radar Appearance Settings

From a radar screen, select Menu > Radar Setup >

Appearance.

NOTE: These settings do not apply to the radar overlay.

Bkgd. Color: Sets the color for the background.

Foreground Clr.: Sets the color scheme for the radar returns.

22).

Look-Ahead Speed: Shifts your present location toward the

bottom of the screen automatically as your speed increases.

Enter your top speed for the best results.

Heading Line: Shows an extension from the bow of the boat in

the direction of travel on the radar screen.

Range Rings: Shows the range rings that help you to visualize

distances on the radar screen.

Bearing Ring: Shows a bearing relative to your heading or

based on a north reference, to help you determine the

bearing to an object shown on the radar screen.

Nav Lines: Shows the navigation lines that indicate the course

you have set using Route To, Auto Guidance, or Go To.

Waypoints: Shows waypoints on the radar screen.

Front-of-Boat Offset

The front-of-boat offset compensates for the physical location of

the radar scanner on a boat, if the radar scanner does not align

with the bow-stern axis.

Measuring the Potential Front-of-Boat Offset

The front-of-boat offset compensates for the physical location of

the radar scanner on a boat, if the radar scanner does not align

with the bow-stern axis.

Using a magnetic compass, take an optical bearing of a

stationary target located within viewable range.

Measure the target bearing on the radar.

If the bearing deviation is more than +/- 1°, set the front-of-

boat offset.

Setting the Front-of-Boat Offset

Before you can set the front-of-boat offset, you must measure

the potential front-of-boat offset.

The front-of-boat offset setting configured for use in one radar

mode is applied to every other radar mode and to the Radar

overlay.

From a Radar screen or the Radar overlay, select Menu >

Radar Setup > Installation > Front of Boat.

Select Up or Down to adjust the offset.

Gauges and Almanac Information

Gauges provide various information about the trip, engine,

environment, and wind, and are available on all chartplotter

models. Numbers, Compass, and Trip gauges are available on

all chartplotters. Wind and Environment gauges require valid

wind data from the NMEA 0183 or NMEA 2000 network. Engine

gauges require a connection to the NMEA 2000 network, so

they are not available on all chartplotter models.