Garmin ECHOMAP PLUS 60 series 소유자 매뉴얼 - 페이지 35

{카테고리_이름} Garmin ECHOMAP PLUS 60 series에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin ECHOMAP PLUS 60 series 50 페이지.
Garmin ECHOMAP PLUS 60 series에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (6 페이지), 빠른 시작 매뉴얼 (8 페이지), 설치 지침 매뉴얼 (6 페이지)

페이지 인쇄

Tack and Gybe

You can set the autopilot to perform a tack or gybe while

heading hold or wind hold is engaged.

Tacking and Gybing from Heading Hold

Engage heading hold

(Engaging the Autopilot, page

Select MENU.

Select an option.

The autopilot steers your boat through a tack or gybe.

Tacking and Gybing from Wind Hold

Before you can engage wind hold, you must have a wind sensor

installed.

Engage wind hold

(Engaging Wind Hold, page

Select MENU.

Select an option.

The autopilot steers your boat through a tack or gybe, and

information about the progress of the tack or gybe appears

on the screen.

Setting a Tack and Gybe Delay

The tack and gybe delay allows you to delay steering a tack and

gybe after you initiate the maneuver.

From the autopilot screen, select MENU > Autopilot Setup >

Sailing Setup > Tack/Gybe Delay.

Select the length of the delay.

If necessary, select Done.

Enabling the Gybe Inhibitor

NOTE: The gybe inhibitor does not prevent you from manually

performing a gybe using the helm or step steering.

The gybe inhibitor prevents the autopilot from performing a

gybe.

From the autopilot screen, select MENU > Autopilot Setup >

Sailing Setup > Gybe Inhibitor.

Select Enabled.

Gauges and Graphs

The gauges and graphs provide various information about the

engine and environment. To view the information, a compatible

transducer or sensor must be connected to the network.

Viewing the Compass

You can view information about your bearing, heading, and

route using the compass.

Select Gauges > Compass.

Viewing Trip Gauges

Trip gauges show information for odometer, speed, time, and

fuel for your present trip.

Select Gauges > Trip.

Resetting Trip Gauges

Select Gauges > Trip > MENU.

Select an option:

• To set all the readings for the present trip to zero, select

Reset Trip.

• To set the maximum speed reading to zero, select Reset

Maximum Speed.

• To set the odometer reading to zero, select Reset

Odometer.

• To set all the readings to zero, select Reset All.

Gauges and Graphs

Viewing Engine and Fuel Gauges

Before you can view engine and fuel gauges, you must be

connected to a NMEA 2000 network capable of sensing engine

and fuel data. See the installation instructions for details.

Select Gauges > Engine.

26).

28).

Selecting the Number of Engines Shown in Gauges

You can show information for up to four engines.

From the engine gauges screen, select MENU > Gauge

Setup > Engine Selection > Number of Engines.

Select an option:

• Select the number of engines.

• Select Auto Configure to automatically detect the number

of engines.

Customizing the Engines Shown in Gauges

Before you can customize how the engines are shown in the

gauges, you must manually select the number of engines

(Selecting the Number of Engines Shown in Gauges, page

From the engine gauges screen, select MENU > Gauge

Setup > Engine Selection > Number of Engines.

Select First Engine.

Select the engine to display in the first gauge.

Repeat for the remaining engine bars.

Enabling Status Alarms for Engine Gauges

You can enable the chartplotter to display engine status alarms.

From the engine gauges screen, select MENU > Gauge

Setup > Status Alarms > On.

When an engine alarms is triggered, a gauge status alarm

message appears and the gauge may become red depending

on the type of alarm.

Enabling Some Engine Gauge Status Alarms

From the engine gauges screen, select MENU > Gauge

Setup > Status Alarms > Custom.

Select one or more engine gauge alarms to turn on or off.

Setting the Fuel Alarm

Before you can set a fuel level alarm, a compatible fuel flow

sensor must be connected to the chartplotter.

You can set an alarm to sound when the total amount of

remaining onboard fuel reaches the level you specify.

Select Settings > Alarms > Fuel > Set Total Fuel Onboard

> On.

Enter the remaining amount of fuel that triggers the alarm,

and select Done.

Setting the Fuel Capacity of the Vessel

Select Settings > My Vessel > Fuel Capacity.

Enter the combined total capacity of the fuel tanks.

Synchronizing the Fuel Data with the Actual Vessel

Fuel

You can synchronize the fuel levels in the chartplotter with the

actual fuel in the vessel when you add fuel to your vessel.

Select Gauges > Engine > MENU.

29).