Garmin ECHOMAP PLUS 60 series 설치 지침 매뉴얼 - 페이지 3

{카테고리_이름} Garmin ECHOMAP PLUS 60 series에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin ECHOMAP PLUS 60 series 6 페이지.
Garmin ECHOMAP PLUS 60 series에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (6 페이지), 빠른 시작 매뉴얼 (8 페이지), 소유자 매뉴얼 (50 페이지)

페이지 인쇄

Connect the red wire to the positive terminal on the battery or

fuse block, and connect the black wire to the negative

terminal.

Power and Data Cable

• The wiring harness connects the device to power and NMEA

0183 devices. 6-inch devices can also use these wires to

share user data, such as waypoints and routes.

• If you are not connecting NMEA 0183 devices or another

chartplotter to share data, disregard the blue and brown

wires.

• The device has one internal NMEA 0183 port that is used to

connect to NMEA 0183 compliant devices.

• If it is necessary to extend the power and ground wires, you

must use 0.82 mm

(18 AWG) or larger wire.

• If it is necessary to extend the NMEA 0183 or alarm wires,

you must use .33 mm

Item

Wire Function

NMEA 0183 internal port Rx (in)

NMEA 0183 internal port Tx (out)

Ground (power and NMEA 0183)

Power

Connecting to a Garmin Device to Share User Data

NOTE: This feature is not available on ECHOMAP Plus 7x/9x

devices. The blue and brown wires on those devices can

connect to NMEA 0183 devices only.

You can connect the ECHOMAP Plus 6x device to a compatible

Garmin device to share user data, such as waypoints. If the

devices are mounted near each other, you can connect the blue

and brown wires. If the devices are mounted too far apart for the

wires to reach, you can connect the devices using a User Data

Sharing Cable (010-12234-06).

Make sure both devices are connected to the same ground.

Complete an action:

• If the devices are mounted near each other, connect the

blue wire from the first device to the brown wire of the

second, and connect the brown wire from the first device

to the blue wire of the second.

• If the devices are not mounted near each other, obtain a

User Data Sharing Cable (010-12234-06), and connect

the devices following the instructions included with the

cable.

On both devices, select Nav Info > Manage Data > User

Data Sharing.

User data is shared between the connected devices. If you

select Clear User Data, data is removed from both connected

devices.

Connecting the Device to a Transducer

Go to

www.garmin.com/transducers

Garmin dealer to determine the appropriate type of transducer

for your needs.

Follow the instructions provided with your transducer to

correctly install it on your boat.

Route the transducer cable to the back of your device, away

from sources of electrical interference.

Connect the transducer cable to the appropriate port on the

cradle.

(22 AWG) wire.

Wire Color

Brown

Blue

Black

Red

or contact your local

Connecting the Cables to the ECHOMAP Plus 6x

Cradle

The connectors on the cables are keyed to fit only in the correct

ports on the ECHOMAP Plus 6x cradle. The connected cables

are held in place by a locking bracket.

Slide the cable locking bracket up from the bottom, and

remove the bracket from the cradle.

Compare the divots

on each port to determine which cable corresponds to each

port.

Fully and firmly insert each cable through a hole in the cradle,

and securely connect each cable to a port.

NOTE: If the cables are not inserted far enough into the

cradle, the connectors may not connect securely to the ports,

and the device may appear to lose power or sonar or may

stop working.

Place the locking bracket

bracket down to lock the cables in place.

There is an audible click when the locking bracket is installed

correctly.

Connecting the Cables to the ECHOMAP Plus 7x/9x

Cradle

The cables connectors fit only in the correct ports on the

ECHOMAP Plus 7x/9x cradle. The connected cables are held in

place by locking rings.

Insert each cable into the appropriate port in the cradle.

Spin the locking ring clockwise to lock the cable to the cradle.

Installing the Device in the Cradle

After the cables are connected to the cradle, you can quickly

place the device in the cradle.

Place the base of the device in the bottom of the cradle.

Tilt the top of the device toward the cradle until it fastens in

place.

There is an audible click when the device is secured in the

cradle.

You should make sure the device is firmly secured in the cradle.

If the model uses a locking bracket, make sure the bracket is

firmly snapped shut. There is an audible click when the device

or locking bracket is installed correctly. If the device is not firmly

secured, it can lose power. The device can also fall out of the

cradle and become damaged if it is not firmly secured.

Removing the Device from the Cradle

Press the release lever

released.

on each cable connector to the keying

over the cables, and slide the

NOTICE

on the cradle until the device is