Garmin ECHOMAP PLUS 70 series 소유자 매뉴얼 - 페이지 27

{카테고리_이름} Garmin ECHOMAP PLUS 70 series에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin ECHOMAP PLUS 70 series 50 페이지.
Garmin ECHOMAP PLUS 70 series에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (8 페이지), 설치 지침 매뉴얼 (6 페이지)

페이지 인쇄

If you are connecting a transducer that was not included with the

chartplotter, you may need to set the transducer type to make

the sonar function properly.

From a sonar view, select MENU > Sonar Setup >

Installation > Transducer Type.

Select the transducer to change.

Select an option:

• If your transducer is listed, select it from the list.

• If you have a 200/77 kHz, dual-beam transducer, select

Dual Beam (200/77 kHz).

• If you have a 200/50 kHz, dual-frequency transducer,

select Dual Frequency (200/50 kHz).

Calibrating the Compass

Before you can calibrate the compass, the transducer must be

installed on the shaft far enough away from the trolling motor to

avoid magnetic interference, and deployed in the water.

Calibration must be of sufficient quality to enable the internal

compass.

NOTE: To use the compass, you must mount the transducer on

the transom or the trolling motor shaft. The compass may not

work when you mount the transducer on the motor.

NOTE: For best results, you should use a heading sensor such

as the SteadyCast

heading sensor. The heading sensor shows

™

the direction the transducer is pointing relative to the boat.

NOTE: Compass calibration is available only for transducers

with an internal compass, such as the PS21-TR transducer.

You can begin turning your boat before calibrating, but you must

fully rotate your boat 1.5 times during calibration.

From an applicable sonar view, select MENU > Sonar Setup

> Installation.

If necessary, select Use AHRS to turn on the AHRS sensor.

Select Calibrate Compass.

Follow the on-screen instructions.

Selecting a Sonar Source

This feature may not be available with all models.

When you are using more than one sonar data source for a

particular sonar view, you can select the source to use for that

sonar view. For example, if you have two sources for Garmin

ClearVü, you can select the source to use from the Garmin

ClearVü sonar view.

Open the sonar view for which you will change the source.

Select MENU > Sonar Setup > Source.

Select the source for this sonar view.

Renaming a Sonar Source

You can rename a sonar source to easily identify that source.

For example, you use "Bow" as the name of the transducer on

the bow of your boat.

To rename a source, you must be in the applicable sonar view

for the source. For example, to rename the Garmin ClearVü

sonar source, you must open the Garmin ClearVü sonar view.

From the sonar view, select MENU > Sonar Setup > Source

> Rename Sources.

Enter the name.

Creating a Waypoint on the Sonar Screen

From a sonar view, select MENU > Pause Sonar.

Select a location.

Select New Waypoint or SELECT.

If necessary, edit the waypoint information, such as the

waypoint name.

Sonar Fishfinder

Pausing the Sonar Display

From a sonar view, select MENU > Pause Sonar.

Measuring Distance on the Sonar Screen

You can measure the distance between two points on the

SideVü sonar view.

From the SideVü sonar view, select .

Select a location on the screen.

Select

A push pin appears on the screen at the selected location.

Select another location.

The distance and angle from the pin is listed in the upper-left

corner.

TIP: To reset the pin and measure from the current location of

the pin, select Set Reference.

Viewing Sonar History

You can scroll the sonar display to view historical sonar data.

NOTE: Not all transducers save historical sonar data.

Select BACK to exit history.

Sonar Sharing

This feature may not be available on all chartplotter models.

You can view the sonar data from other compatible ECHOMAP

models connected on the Garmin Marine Network.

Each chartplotter on the network can display sonar data from

every compatible sonar module and transducer on the network,

no matter where the chartplotters and transducers are mounted

on your boat. For example, from one ECHOMAP Plus 93sv

device mounted at the back of the boat, you can view the sonar

data from another ECHOMAP Plus device and Garmin ClearVü

transducer mounted at the front of your boat.

When sharing sonar data, the values of some sonar settings,

such as Range and Gain, are synchronized across the devices

on the network. The values of other sonar settings, such as the

Appearance settings, are not synchronized and should be

configured on each individual device. In addition, the scroll rates

of the various traditional and Garmin ClearVü sonar views are

synchronized to make the split views more cohesive.

NOTE: Using multiple transducers simultaneously can create

cross talk, which can be removed by adjusting the Interference

sonar setting.

Adjusting the Level of Detail

You can control the level of detail and noise shown on the sonar

screen either by adjusting the gain for traditional transducers or

by adjusting the brightness for Garmin ClearVü transducers.

If you want to see the highest intensity signal returns on the

screen, you can lower the gain or brightness to remove lower

intensity returns and noise. If you want to see all return

information, you can increase the gain or brightness to see more

information on the screen. This also increases noise, and can

make it more difficult to recognize actual returns.

From a sonar view, select MENU.

Select Gain or Brightness.

Select an option:

• To increase or decrease the gain or brightness manually,

select Up or Down.

• To allow the chartplotter to adjust the gain or brightness

automatically, select an automatic option.