Garmin ECHOMAP PLUS 70 series 소유자 매뉴얼 - 페이지 31

{카테고리_이름} Garmin ECHOMAP PLUS 70 series에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin ECHOMAP PLUS 70 series 50 페이지.
Garmin ECHOMAP PLUS 70 series에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (8 페이지), 설치 지침 매뉴얼 (6 페이지)

페이지 인쇄

obligation of the vessel operator to ensure safe operation of the

vessel.

This alarm is available only with Panoptix FrontVü transducers.

You can set an alarm to sound when the depth is below a

specified level. For best results, you should set the bow offset

when using the front collision alarm

page

25).

From the FrontVü sonar view, select MENU > FrontVü

Alarm.

Select On.

Enter the depth at which the alarm is triggered, and select

Done.

On the FrontVü screen, a depth line shows the depth at which

the alarm is set. The line is green when you are in a safe depth.

The line turns yellow when you are going faster than the forward

range gives you time to react (10 seconds). It turns red and

sounds an alarm when the system detects an obstruction or the

depth is less than the entered value.

The ability to effectively avoid running aground with FrontVü

sonar decreases as your speed rises above 8 knots.

LiveVü and FrontVü Appearance Settings

From a LiveVü or FrontVü Panoptix sonar view, select MENU >

Sonar Setup > Appearance.

Color Scheme: Sets the color palette.

Color Gain: Adjusts the intensity of colors shown on the screen.

You can select a higher color gain value to see targets higher

in the water column. A higher color gain value also allow you

to differentiate low intensity returns higher in the water

column, but this causes a loss in the differentiation of the

returns at the bottom. You can select a lower color gain value

when targets are near the bottom, to help you distinguish

between targets and high intensity returns such as sand,

rock, and mud.

Trails: Sets the how long the trails appear on the screen. The

trails show the movement of the target.

Bottom Fill: Colors the bottom brown to distinguish it from the

water returns.

Grid Overlay: Shows a grid of range lines.

Scroll History: Shows the sonar history in a traditional sonar

view.

RealVü Appearance Settings

From a RealVü sonar view, select MENU > Sonar Setup >

Appearance.

Point Colors: Sets a different color palette for the sonar return

points.

Bottom Colors: Sets the color scheme for the bottom.

Bottom Style: Sets the style for the bottom. When you are in

deep water, you can select the Points option and manually

set the range to a shallower value.

Color Key: Shows a legend of the depths the colors represent.

Panoptix Transducer Installation Settings

From a Panoptix sonar view, select MENU > Sonar Setup >

Installation.

Install Depth: Sets the depth below the water line where the

Panoptix transducer is mounted. Entering the actual depth at

which the transducer is mounted results in a more accurate

visual presentation of what is in the water.

Bow Offset: Sets the distance between the bow and the forward

view Panoptix transducer installation location. This allows

you to view the forward distance from the bow instead of the

transducer location.

Sonar Fishfinder

(Setting the Bow Offset,

CAUTION

This applies to Panoptix transducers in the FrontVü, LiveVü

Forward, and RealVü 3D Forward sonar views.

Beam Width: Sets the width of the down view Panoptix

transducer beam. Narrow beam widths allow you to see

deeper and farther. Wider beam widths allow you to see

more coverage area.

This applies to Panoptix transducers in the FrontVü, LiveVü

Down, and LiveVü Forward sonar views.

Use AHRS: Enables the internal attitude heading and reference

system (AHRS) sensors to detect the installation angle of the

Panoptix transducer automatically. When this setting is

turned off, you can enter the specific installation angle for the

transducer using the Pitch Angle setting. Many forward view

transducers are installed at a 45-degree angle and down

view transducers are installed at a zero-degree angle.

Flipped: Sets the orientation of the Panoptix sonar view when

the down view transducer is installed with the cables pointing

toward the port side of the boat.

This applies to Panoptix transducers in the LiveVü Down,

RealVü 3D Down, and RealVü 3D Historical sonar views.

Calibrate Compass: Calibrates the internal compass in the

Panoptix transducer

(Transducer Installation Settings,

page

23).

This applies to Panoptix transducers with an internal

compass, such as the PS21-TR transducer.

Orientation: Controls if the transducer is in down or forward

installation mode. The Auto setting uses the AHRS sensor to

determine the orientation.

This applies to PS22 and LiveScope transducers.

Focus: Adjusts the sonar view to compensate for the speed of

sound in water. The Auto setting uses the temperature of the

water to calculate the speed of sound.

This applies to LiveScope transducers.

Restore Sonar Defaults: Restores the sonar settings to the

factory default values.

Setting the Bow Offset

For forward view Panoptix transducers, you can enter a bow

offset to compensate the forward distance readings for the

transducer installation location. This allows you to view the

forward distance from the bow instead of the transducer

installation location.

This feature applies to Panoptix transducers in the FrontVü,

LiveVü Forward, and RealVü 3D Forward sonar views.

Measure the horizontal distance

bow.

From an applicable sonar view, select MENU > Sonar Setup

> Installation > Bow Offset.

from the transducer to the