Garmin ECHOMAP PLUS 90 series 소유자 매뉴얼 - 페이지 32

{카테고리_이름} Garmin ECHOMAP PLUS 90 series에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin ECHOMAP PLUS 90 series 50 페이지. Navigation portable plus for bmw
Garmin ECHOMAP PLUS 90 series에 대해서도 마찬가지입니다: 소유자 매뉴얼 (40 페이지), 설치 지침 매뉴얼 (6 페이지), 빠른 시작 매뉴얼 (8 페이지), 설치 지침 매뉴얼 (6 페이지)

페이지 인쇄

Enter the distance measured, and select Done.

On the applicable sonar view, the forward range shifts by the

distance you entered.

Autopilot

You can use the autopilot feature only at a station installed next

to a helm, throttle, and helm control device.

You are responsible for the safe and prudent operation of your

vessel. The autopilot is a tool that enhances your capability to

operate your boat. It does not relieve you of the responsibility of

safely operating your boat. Avoid navigational hazards and

never leave the helm unattended.

Always be prepared to promptly regain manual control of your

boat.

Learn to operate the autopilot on calm and hazard-free open

water.

Use caution when operating the autopilot near hazards in the

water, such as docks, pilings, and other boats.

NOTE: This feature is only available on models with NMEA

2000 network capabilities.

The autopilot system continuously adjusts the steering of your

boat to maintain a constant heading (heading hold). The system

also allows manual steering and several modes of automatic-

steering functions and patterns.

When the compatible chartplotter is connected to a compatible

Garmin autopilot system, you can engage and control the

autopilot from the chartplotter.

For information about compatible Garmin autopilot systems, go

to garmin.com.

Autopilot Screen

Actual heading

Intended heading (heading the autopilot is steering toward)

Actual heading (when in standby mode)

Intended heading (when engaged)

Rudder position indicator (This functionality is available only when a

rudder sensor is connected.)

Adjusting the Step Steering Increment

From the Autopilot screen, select MENU > Autopilot Setup >

Step Turn Size.

Select an increment.

Setting the Power Saver

You can adjust the level of rudder activity.

From the autopilot screen, select MENU > Autopilot Setup >

Power Mode Setup > Power Saver.

Select a percentage.

Selecting a higher percentage reduces rudder activity and

heading performance. The higher the percentage, the more

the course deviates before the autopilot corrects it.

WARNING

TIP: In choppy conditions at low speeds, increasing the

Power Saver percentage reduces rudder activity.

Selecting the Preferred Heading Source

For best results, use the autopilot CCU internal compass for the

heading source. Using a third-party GPS compass can cause

the data to be delivered erratically and may result in excessive

delays. The autopilot needs timely information, and therefore

cannot often use third-party GPS compass data for GPS

location or speed. If a third-party GPS compass is used, the

autopilot will likely report loss of navigation data and speed

source periodically.

If you have more than one heading source on the network, you

can select a your preferred source. The source could be a

compatible GPS compass or a magnetic heading sensor.

From the autopilot screen, select MENU > Autopilot Setup >

Preferred Sources

Select a source.

If the selected heading source is unavailable, the autopilot

screen does not display any data.

Engaging the Autopilot

When you engage the autopilot, the autopilot takes control of the

helm and steers the boat to maintain your heading.

From any screen, select Engage.

Your intended heading shows in the center of the Autopilot

screen.

Steering Patterns

You are responsible for the safe operation of your boat. Do not

begin a pattern until you are certain that the water is clear of

obstacles.

The autopilot can steer the boat in preset patterns for fishing,

and it can also perform other specialty maneuvers such as U-

turns and Williamson turns.

Following the U-Turn Pattern

You can use the u-turn pattern to turn the boat around 180

degrees and maintain the new heading.

From the autopilot screen, select MENU > Pattern Steering

> U-Turn.

Select Engage Port or Engage Starboard.

Setting Up and Following the Circles Pattern

You can use the circles pattern to steer the boat in a continuous

circle, in a specified direction, and at a specified time interval.

From the autopilot screen, select MENU > Pattern Steering

> Circles.

If necessary, select Time, and select a time for the autopilot

to steer one complete circle.

Select Engage Port or Engage Starboard.

Setting Up and Following the Zigzag Pattern

You can use the zigzag pattern to steer the boat from port to

starboard and back, over a specified time and angle, across

your present heading.

From the autopilot screen, select MENU > Pattern Steering

> Zigzag.

If necessary, select Amplitude, and select a degree.

If necessary, select Period, and select a length of time.

Select Engage Zigzag.

NOTICE

WARNING

Autopilot