Garmin ECHOMAP PLUS 90 series 소유자 매뉴얼 - 페이지 42

{카테고리_이름} Garmin ECHOMAP PLUS 90 series에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin ECHOMAP PLUS 90 series 50 페이지. Navigation portable plus for bmw
Garmin ECHOMAP PLUS 90 series에 대해서도 마찬가지입니다: 소유자 매뉴얼 (40 페이지), 설치 지침 매뉴얼 (6 페이지), 빠른 시작 매뉴얼 (8 페이지), 설치 지침 매뉴얼 (6 페이지)

페이지 인쇄

Calibrating a Water Speed Device

If you have a speed-sensing transducer connected to the

chartplotter, you can calibrate that speed-sensing device to

improve the accuracy of water-speed data displayed by the

chartplotter.

Select Settings > My Vessel > Calibrate Water Speed.

Follow the on-screen instructions.

If the boat is not moving fast enough or the speed sensor is

not registering a speed, a message appears.

Select OK, and safely increase the boat speed.

If the message appears again, stop the boat, and ensure the

speed-sensor wheel is not stuck.

If the wheel turns freely, check the cable connections.

If you continue to get the message, contact Garmin product

support.

Setting the Fuel Capacity of the Vessel

Select Settings > My Vessel > Fuel Capacity.

Enter the combined total capacity of the fuel tanks.

Synchronizing the Fuel Data with the Actual Vessel

Fuel

You can synchronize the fuel levels in the chartplotter with the

actual fuel in the vessel when you add fuel to your vessel.

Select Gauges > Engine > MENU.

Select an option:

• After you have filled up all the fuel tanks on the vessel,

select Fill Up All Tanks. The fuel level is reset to

maximum capacity.

• After you have added less than a full tank of fuel, select

Add Fuel to Boat, and enter the amount added.

• To specify the total fuel in the vessel tanks, select Set

Total Fuel Onboard, and enter the total amount of fuel in

the tanks.

Customizing Engine Gauge and Fuel Gauge Limits

You can configure the upper and lower limits and the range of

desired standard operation of a gauge.

NOTE: Not all options are available for all gauges.

From an applicable gauges screen, select MENU > Gauge

Setup > Set Gauge Limits.

Select a gauge to customize.

Select Gauge Limits > Custom.

Select an option:

• To set the minimum value of the standard operating

range, select Rated Min..

• To set the maximum value of the standard operating

range, select Rated Max..

• To set the lower limit of the gauge lower than the rated

minimum, select Scale Min..

• To set the upper limit of the gauge higher than the rated

maximum, select Scale Max..

Select the limit value.

Repeat steps 4 and 5 to set additional gauge limits.

Communications Settings

NOTE: Some settings and options require additional charts or

hardware.

Select Settings > Communications.

Serial Port: Sets the input/output format for the serial port to

use when connecting the chartplotter to external NMEA

devices, computers, or other Garmin devices.

NMEA 0183 Setup: Sets the NMEA 0183 sentences the

chartplotter transmits, how many digits to the right of the

decimal point are transmitted in a NMEA output, and how

waypoints are identified

NMEA 2000 Setup: Allows you to view and label the devices on

the NMEA 2000 network

Marine Network: Allows you to view the devices with which you

are sharing maps, sonar, or radar. Not available on all

chartplotter models.

NOTE: You can only view networked data on a model that

supports that data. For example, you cannot view networked

radar on model that does not support radar.

Wi-Fi Network: Allows you set up the Wi‑Fi network

‑ Fi Wireless Network, page

the Wi

NMEA 0183

The chartplotters support the NMEA 0183 standard, which is

used to connect various NMEA 0183 devices, such as VHF

radios, NMEA instruments, autopilots, wind sensors, and

heading sensors.

To connect the chartplotter to optional NMEA 0183 devices, see

the chartplotter installation instructions.

The approved NMEA 0183 sentences for the chartplotter are

GPAPB, GPBOD, GPBWC, GPGGA, GPGLL, GPGSA, GPGSV,

GPRMB, GPRMC, GPRTE, GPVTG, GPWPL, GPXTE, and

Garmin proprietary sentences PGRME, PGRMM, and PGRMZ.

This chartplotter also includes support for the WPL sentence,

DSC, and sonar NMEA 0183 input with support for the DPT

(depth) or DBT, MTW (water temperature), and VHW (water

temperature, speed, and heading) sentences.

NMEA 0183 Settings

Select Settings > Communications > NMEA 0183 Setup.

Sounder: Enables NMEA 0183 output sentences for the

sounder (if applicable).

Route: Enables NMEA 0183 output sentences for routes.

System: Enables NMEA 0183 output sentences for system

information.

Garmin: Enables NMEA 0183 output sentences for Garmin

proprietary sentences.

Posn Precision: Adjusts the number of digits to the right of the

decimal point for transmission of NMEA output.

Waypoint IDs: Sets the device to transmit waypoint names or

numbers via NMEA 0183 while navigating. Using numbers

may resolve compatibility issues with older NMEA 0183

autopilots.

Diagnostics: Displays NMEA 0183 diagnostic information.

Defaults: Restores the NMEA 0183 settings to the original

factory defaults.

NMEA 2000 Settings

Select Settings > Communications > NMEA 2000 Setup.

Device List: Displays the devices connected to the network.

Label Devices: Changes the labels for available connected

devices.

Naming Devices and Sensors on the Network

You can name devices and sensors connected to the Garmin

Marine Network and the NMEA 2000 network.

Select Settings > Communications.

Select Marine Network or NMEA 2000 Setup > Device List.

Select a device from the list on the left.

Select Change Name.

Enter the name, and select Done.

(NMEA 0183 Settings, page

(NMEA 2000 Settings, page

(Setting Up

37).

Device Configuration

36).