Garmin GHP 10 Marine Autopilot System 설치 지침 매뉴얼 - 페이지 37
{카테고리_이름} Garmin GHP 10 Marine Autopilot System에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GHP 10 Marine Autopilot System 48 페이지. Tachometer reference
Garmin GHP 10 Marine Autopilot System에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (21 페이지), 설치 지침 매뉴얼 (26 페이지), 기술 참조 (42 페이지), 적합성 선언 (1 페이지), 참조 (1 페이지)
페이지 인쇄
Evaluating the Results of the Autopilot Configuration
When the Dockside and Sea Trial Wizards are complete, test the autopilot to be sure it is configured correctly. Test the autopilot first at
slow speeds (below planing), and then test the autopilot at planing speeds.
To test the autopilot configuration:
1. Drive the boat in one direction with the autopilot engaged (heading hold). The boat should not oscillate significantly; however, a
small amount of oscillation is normal.
2. Turn the boat in one direction using the autopilot.
•
Does the boat turn too aggressively or too sluggishly?
•
When you release the turn button, the boat should overshoot the turn and quickly correct the heading to the point at which you
released the button. You will notice that the faster you are going, the greater the boat will overshoot the turn.
3. If the autopilot is configured properly at slow speeds, repeat these tests at planing speed.
Adjusting the Autopilot Configuration
If you feel that the heading hold oscillates significantly or that the autopilot does not quickly correct the heading when turning, make
slight adjustments to the autopilot gain.
If you feel that the autopilot turns too aggressively or too sluggishly, make slight adjustments to the acceleration limiter.
to adjust the autopilot Gain settings:
notE: When you manually adjust the rudder gain (or counter gain), make small adjustments, and adjust only one value at a time.
Test the change before entering any further adjustments.
1. Power the GHP 10 on using the advanced configuration power-on procedure on
2. On the GHC 10, select
the rudder gain adjustments. There are two types of gain settings at both low and high speeds:
•
Rudder Gain—Adjusts how tightly the rudder holds the heading and makes turns. If you set this value too high, the autopilot
may be overactive, attempting to constantly adjust the heading at the slightest deviation. An overactive autopilot can cause
excess wear and tear on the autopilot pump.
•
Counter Gain—Adjusts how tightly the rudder corrects the turn overshoot. If you set this value too high, the autopilot can
overshoot the turn again when attempting to counter the original turn.
3. Adjust the setting that you want to change, and test the adjustment. Repeat steps 2 and 3 until the GHP 10 performance is
satisfactory.
to adjust the acceleration limiter settings:
notE: When you manually adjust the acceleration limiter, make small adjustments. Test the change before entering any further
adjustments.
1. Power on the GHP 10 using the advanced configuration power-on procedure on
2. On the GHC 10, select
access the acceleration limiter adjustments.
3. Adjust the setting and test the adjustment. Repeat steps 2 and 3 until the GHP 10 performance is satisfactory.
GHP 10 Marine Autopilot System Installation Instructions
Menu
>
Setup
>
Dealer Autopilot Configuration
Menu
>
Setup
>
Dealer Autopilot Configuration
page
38.
>
turn Fine tuning Setup
page
38.
>
turn Fine tuning Setup
>
Rudder Gains
to access
>
Acceleration Limiter
to
7