Garmin GPS 16-HVS 사용 설명서 - 페이지 21

{카테고리_이름} Garmin GPS 16-HVS에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GPS 16-HVS 30 페이지. Instruction manual
Garmin GPS 16-HVS에 대해서도 마찬가지입니다: 참조 매뉴얼 (1 페이지), 기술 사양 (40 페이지), 기술 사양 (37 페이지), 적합성 선언 (2 페이지), 사용 설명서 (30 페이지)

페이지 인쇄

1. Wiring

Appendix A. CR23X/CR10X Programs

24: Z=F x 10^n (P30)

1: -1

2: 00

3: 6

25: End (P95)

26: End (P95)

End Program

A.1.6 Troubleshooting

A-8

n, Exponent of 10

Z Loc [ Quality ]

This is a blank page.

The first step is to verify that it really does not work. With the GPS16-HVS

running and the datalogger program running, look at the input location for GPS

Quality Number. This location will show a one when the GPS16-HVS output

is picked up by the datalogger. The input location for parsed time and position

are good locations to check. The location for seconds should update every time

the GPS data is updated.

If the GPS time and position data are not shown in the input locations, check

the communication cable wiring.

If the GPS16-HVS data is not correct every program table execution but

correct sometimes, check the P15 time-out. It may need a longer time-out.

Also check the P15 maximum number of characters to receive, usually 100 is

enough. Check the P15 termination character; it should be set to 42 (*). The

termination character should also work if set to 13 or 10. Also check the

buffering and filter. Buffering should be turned off. On a CR23X, index

parameter 2. The CR10X does not buffer data.

For P15 to properly read the $GPGGA string, P15 must be executing while the

$GPGGA string starts and finishes. The P15 time-out needs to be long enough

to pick up the string. The string is output once a second. If P15 starts to

execute while the GPS16-HVS is sending the string, P15 must wait until the

string is sent again plus the amount of time it takes to send the string. It

shouldn't need more than 1.5 seconds. P15 time-out is in units of 0.01

seconds, 100 = 1 second. A longer time-out will force the datalogger to wait

until the time-out has expired or the termination character is received or the

maximum number of characters are received. If the data in input locations

seem to move from the proper input location to another input location, P15 is

stopping before the entire string has been read. An example is latitude being

displayed in the time field, then in the latitude field. P15 works best when P15

quits reading data because the termination character has been read. Using the

PPS to trigger subroutine 98 is the best way to start P15 just before the GPS16-

HVS sends the $GPGGA string. If the PPS signal pulls C8 high while the

datalogger is in the middle of executing an instruction, it may not be able to run

subroutine 98 before the $GPGGA string has started, which will cause the

datalogger to miss the data string. Turning on the data buffering (CR23X only)

may remedy the problem. Lengthening the serial time-out to allow P15 to

execute for 2 cycles of NMEA output may help. Otherwise the SDM-SIO4

may be required or the datalogger program will need to be simplified.