Garmin GPSMAP 172 설치 지침

{카테고리_이름} Garmin GPSMAP 172에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GPSMAP 172 3 페이지. Rugged, waterproof, fixed-mount gps navigator
Garmin GPSMAP 172에 대해서도 마찬가지입니다: 사양 (2 페이지), 빠른 참조 (2 페이지)

페이지 인쇄

Contents:

Flush Mount Pocket:

Mounts to the bulkhead

and retains the unit

Tool List (Not Included)

Jig Saw

7mm Wrench

Drill and 3/8' Drill Bit

Masking Tape

Thread Locking Compound — (Optional)

Safety Goggles and Dust Mask for drilling

Please read through these instructions thoroughly before attempting installation. Make

sure you completely understand these instructions before you begin. When in doubt, seek

professional assistance. Be sure the cables will reach the unit and transducer location before

beginning installation. Please check the packing list above. If you are missing any items,

please contact your Garmin dealer. Be sure to wear safety goggles and a dusk mask when

drilling and cutting.

Installing the Flush Mount Pocket

1. Using the supplied Mounting Template, locate a suitable mounting location and

tape the template in place. Be sure to check behind the installation area to

avoid cutting or drilling into wiring, cables, etc.

2. Drill a 3/8" hole at the location in di cat ed on the template as a starting point.

Then, using the Jig Saw, cut the panel along the bold line. Be sure that your

initial cut does not go outside the line that in di cates the inside edge of the

pocket (Figure 1).

3. Using a file or sandpaper, remove any burrs from the open ing. Test fit the

Flush Mount Pocket and make any ad just ments to correct the fit. The Flush

Mount Pocket should not fit tightly at the cutouts on the sides of the pocket.

Approximately 1/8" clearance is necessary for the unit to lock in properly.

4. Install the four Foam Rubber Pads in the pocket at the locations indicated in

Figure 2. To install the pads, peel the lining off of the back and install with the

sticky side against the pocket.

5. Insert the pocket in the panel (the Garmin logo should be positioned at the

top). Install a M4 Hex Head Screw through the pocket and the corresponding

hole in the Metal Retaining Bracket. Start a 4mm Hex Nut on the screw. Repeat

the process until all 4 nuts are started (Figure 3). Tighten the M4 nuts using a

7mm wrench or socket. Avoid overtightening, which will distort the pocket

and prevent the unit from snapping in properly. Install and tighten the second

Hex Nut on all four Mounting Studs to lock the first one in place. If operating

in a high vibration environment it is recommended that you use a thread

locking compound on the M4 Hex Head Screws.

6. Secure the cable to the rectangular slot along the top of the Flush Mount

Pocket or one of the metal retaining brack ets with the wire tie provided in the

kit. Leave approximately 18" of cable extending through the pocket to aid in

the installation and removal of the unit.

Flush Mount Installation Instructions

(External Antenna Versions Only)

Mounting Hardware:

A - Foam Rubber Pads (4)

B - M4 Hex Head Screws (4)

C - M4 Hex Nuts (8)

D - Reusable Cable Tie (1)

E - Metal Retaining Brackets (2)

CUT ALONG BOLD LINE

OUTSIDE EDGE OF POCKET

A PLACE TO BEGIN CUTTING

Dashed lines indicate the actual

outline of the pocket. Cut along

bold line to provide clearance for

Detent Plate operation.

CUT ALONG BOLD LINE

TRIM ALONG DASHED LINE

Figure 1

Rubber Pad Location

Figure 2

Wire Tie Slot

Boat Panel

Mounting Pocket

M4 Hex

Head

Metal Retaining Bracket

Figure 3

3/8"

DRILL A HOLE FOR

M4 Machine Nuts