Garmin GPSMAP 215 소유자 매뉴얼 - 페이지 14

{카테고리_이름} Garmin GPSMAP 215에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Garmin GPSMAP 215 18 페이지.

페이지 인쇄

Select an option:

• To send all DSC-call data from this vessel, select ON.

• To send DSC-distress-call data only from this vessel,

select OFF.

Repeat this process for each vessel in your directory.

Select BACK to save your changes and exit the menu.

System Settings

Select MENU > SYSTEM.

DISPLAY: Sets the backlight and contrast levels.

BEEPER: Sets the volume or disables the beeper tone that

sounds when you press a key or turn a dial.

AUTO POWER-ON: Sets the radio to turn on automatically

when it receives power.

LANGUAGE: Sets the language for the radio.

INT GPS SETUP: Turns on or off the internal GPS antenna.

Number Settings

You can customize the numbers shown on the home screen of

the radio.

Select MENU > SYSTEM > NUMBERS.

LAT/LONG: Shows or hides the latitude and longitude numbers

provided by the GPS position, or from manually-entered

position data.

TIME: Shows or hides the time provided by the GPS acquisition,

or from manually-entered information.

NOTE: The time updates automatically only if you acquire a

GPS position. When you enter your time and position

manually, the time shown does not update automatically. For

manually entered position and time data, the time of entry is

always shown on the home screen, even if you hide the time

with this setting.

COG/SOG: Shows or hides course-over-ground (COG) and

speed-over-ground (SOG) information.

NOTE: You must acquire a GPS position to show course-

over-ground (COG) and speed-over-ground (SOG)

information.

Units Settings

You can set the unit of measure used for values shown on the

radio.

Select MENU > SYSTEM > UNITS.

SPEED: Sets the unit of measure shown for speed-related

fields, such as speed-over-ground.

TIME > FORMAT: Sets the time format.

HEADING: Sets the radio to show all heading calculations, such

as Course Over Ground (COG), using true or magnetic north.

NOTE: If the radio is configured for NMEA 2000

communication, the heading unit is set to AUTO, and shows

heading data based on the information provided over the

network. This setting cannot be changed.

Configuring the Time Offset

You can show the local time rather than Universal Coordinated

Time (UTC). When you adjust for local time, LOC appears after

the time on the home screen.

NOTE: When you make a DSC call, the time is sent in UTC

format.

Select MENU > SYSTEM > UNITS > TIME > OFFSET.

Turn the SELECT dial to adjust the time offset from UTC.

Select OK.

Selecting the Frequency Band

You can switch between the USA, International, or Canadian

frequency bands

(Channel Lists, page

NOTE: Not all frequency bands are available on all device

models.

Select MENU > CHANNEL > FREQUENCY BAND.

Select a frequency band.

Changing a Channel Name

Channel names appear on the home screen using nine

characters. If a channel name is longer than nine characters, the

full name scrolls across the top of the screen, then switches to

the short name. You can change the name of a channel to

reflect a local meaning.

Select MENU > CHANNEL > NAME.

Turn the SELECT dial to select a channel, and select OK.

Change the name of the channel

Select ACCEPT.

Restoring Factory Settings

You can restore the radio to the default factory settings. When

you restore the radio to factory settings, all system changes and

customizations are lost. Restoring factory settings deletes the

call logs, but retains group entries, directory entries, the MMSI

number, and the ATIS ID.

Select MENU > SYSTEM > SYSTEM INFO > RESET.

Select YES to confirm the reset.

Appendix

Alarms and Messages

BATTERY ALRM: Sounds when the battery reaches a specified

low or high voltage. Check the battery wiring.

WX: Sounds when you set a weather alarm and the radio

detects an incoming weather alert

Broadcasts and Alerts, page

automatically to the weather channel that is broadcasting the

alert.

GPS ALARM: Sounds first when GPS data from a NMEA

network or position data entered manually is more than four

hours old. Sounds again when GPS data from a NMEA

network or position data entered manually is more than 23.5

hours old

(Manual Position Information, page

POSITION TRACKING: Appears after five consecutive failed

attempts to request position information from a vessel

(Position Tracking, page

Channel Lists

The International, USA, and Canadian channel lists are

available online for reference. You are responsible for the

correct use of channels according to local regulations.

• To view the latest international channel list, go to

www.navcen.uscg.gov/?pageName=apps18.

• To view the latest USA channel list, go to

www.navcen.uscg.gov/?pageName=mtVhf.

• To view the latest Canadian channel list, go to

/eic/site/smt-gst.nsf/eng/sf01011.html#sched1.

10).

(Entering Text, page

(NOAA

Weather

4). The radio tunes

8).

7).

www.ic.gc.ca

System Settings

4).